Transcript Document

I/O Devices
CT101 – Computing Systems
Contents
• Input devices
–
–
–
–
Keyboard
Mouse
Optical Readers
Card Readers
• Output devices
– Printer
• Inkjet printers
• Laser Printers
– Monitor
• CRT
Input Devices
• The following section discusses the functioning of a
number of input devices
• Input devices allow the user to input information
(data) into the computer for analysis or storage, as
well as give commands to the computer
• Examples of input devices are keyboards, scanners,
mice, bar-wands, and touch screens
Keyboard
• The keyboard is the most widely used means of entering
information into a computer.
• Pressing a key on the keyboard generates a code that
represents the character associated with the key
• The two main codes associated with computers are ASCII
(American Standard Code for Information Interchange) and
EBCDIC (Extended Binary Coded Decimal Interchange
Code)
– ASCII is a seven bit code, so characters generated by the keyboard
are made available as a seven bit code (a total of 128 different
combinations)
– EBCDIC used by IBM and is not used anymore
Keyboard
• A typical keyboard has four basic types of keys:
–
–
–
–
Typing keys
Numeric keypad
Function keys
Control keys
• ASCII codes:
–
–
–
–
00-1F Control Codes
20-3F Punctuation and digits
40-5F Uppercase
60-7F Lowercase
• Control codes are used to control devices like printers and modems,
and to position the cursor. For instance, FF stands for form feed, and
HT stands for horizontal tab. Control codes are generated on a
standard keyboard by holding down the Ctrl key, and whilst it is
depressed, pressing another key
– For example, pressing the key combination CTRL-A generates the code
sequence SOH, and pressing CTRL-R generates the code sequence DC2
Keyboard
• Interface
– RS232, PS2 and USB
– Usually power, ground, clock and data signals
• Types
– QWERTY (used in PC)
– DVORAK
– Microsoft ergonomic keyboard
Keyboard Technologies
• Keyboards use a variety of switch technologies.
• It is interesting to note that we generally like to have some
audible and tactile response to our typing on a keyboard.
– We want to hear the keys "click" as we type, and we want the keys
to feel firm and spring back quickly as we press them.
• Different technologies:
–
–
–
–
Contact switch keyboard
Ferrite core switch keyboard
Magnetic reed switch keyboard
Mercury contact switch keyboard
Contact switch keyboard
• Contact switch is the most common
form of keyboard switch
• Pressing the plunger causes the
contacts to touch (or separate), thus
providing a circuit closure (or
circuit open)
• Circuitry is often used to eliminate
the “bouncing” effect, else false
readings are obtained
Ferrite core switch
• A small ferrite core, mounted on the base of
the switch, has two wires (a drive and sense
wire) attached through its center
• A current pulse is applied to the drive wire,
which is sensed on the sense wire
• The ferrite core is held in a state of saturation
by a small magnet attached to the plunger.
This prevents the current pulse from being
transferred to the sense wire
• When the plunger is pressed, the magnet
moves away from the ferrite core, bringing the
core out of saturation and allowing the sense
wire to pick up the current pulse on the drive
wire
• This type of switch is non-contacting, zero
bounce and has a long life
Other contact switch keyboards
• Magnetic reed switch
– A reed switch comprises a pair of contacts
enclosed in sealed glass envelope
– The contacts are forced together or apart by
applying an external magnetic field. The
magnetic field can be generated by a small
permanent magnet attached to the plunger
• Mercury contact switch
– Two contacts are enclosed in a small
flexible tube, which is filled with a small
amount of mercury
– When the plunger is pressed, the flexible
tube is compressed and causes the mercury
to short with the two contacts, completing
the circuit.
Keyboard encoders
• The keyboard encoder
controls the keyboard
switches and generates a
unique code for each key
• It is an integrated circuit
or small processor, and
handles the key switches in
a matrix of rows and
columns
• The encoder has the task of detecting when a key has been depressed,
identifying the key, and generating the code for the key
• The encoder enables each row in turn, and checks for a change in state
in the column lines. If there is a change in state, this means a key has
been depressed. The row and column values are used to look up a
table which returns the key value
Keyboard encoders
•
•
•
•
•
The key matrix is the grid of circuits underneath the keys. In all keyboards each circuit is broken at the
point below a specific key.
Pressing the key bridges the gap in the circuit, allowing a tiny amount of current to flow through. The
processor monitors the key matrix for signs of continuity at any point on the grid.
When it finds a circuit that is closed, it compares the location of that circuit on the key matrix to the
character map in its ROM. The character map is basically a comparison chart for the processor that tells
it what the key at x,y coordinates in the key matrix represents.
If more than one key is pressed at the same time, the processor checks to see if that combination of keys
has a designation in the character map. For example, pressing the a key by itself would result in a small
letter "a" being sent to the computer. If you press and hold down the Shift key while pressing the a key,
the processor compares that combination with the character map and produces a capital letter "A.“
The character map in the keyboard can be superseded by a different character map provided by the
computer. This is done quite often in languages whose characters do not have English equivalents. Also,
there are utilities for changing the character map from the traditional QWERTY to DVORAK or another
custom version
Keyboard summary
• The standard PC has a QWERTY keyboard which
uses ASCII codes.
• Control codes are used to control devices like
printers, modems and terminals and are generated
using the CTRL key
• A keyboard encoder is a device which handles the
key presses and converts them to an ASCII code
Mouse
• The main goal of any mouse is to translate the motion of your hand
into signals that the computer can use.
• Traditional mice do the translation using five components:
– A ball inside the mouse touches the desktop and rolls when the mouse moves
– Two rollers inside the mouse touch the ball. One of the rollers is oriented so
that it detects motion in the X direction, and the other is oriented 90 degrees to
the first roller so it detects motion in the Y direction. When the ball rotates, one
or both of these rollers rotate as well
Mouse
• Components:
– The rollers each connect to a shaft, and the shaft spins a disk with holes in it. When a
roller rolls, its shaft and disk spin
– On either side of the disk there is an infrared LED and an infrared sensor. The holes in
the disk break the beam of light coming from the LED so that the infrared sensor sees
pulses of light. The rate of the pulsing is directly related to the speed of the mouse and
the distance it travels
– An on-board processor chip reads the pulses from the infrared sensors and turns them
into binary data that the computer can understand. The chip sends the binary data to the
computer through the mouse's cord
Mouse data interface
•
•
Whenever the mouse moves or the user clicks a button, the mouse
sends 3 bytes of data to the computer.
The first byte's 8 bits contain:
–
–
–
–
–
–
–
–
•
•
Left button state (0 = off, 1 = on)
Right button state (0 = off, 1 = on)
0
1
X direction (positive or negative)
Y direction
X overflow (the mouse moved more than 255 pulses in 1/40th of a second)
Y overflow
The next 2 bytes contain the X and Y movement values, respectively.
These 2 bytes contain the number of pulses that have been detected in
the X and Y direction since the last packet was sent. The data is sent
from the mouse to the computer serially on the data line, with the clock
line pulsing to tell the computer where each bit starts and stops.
Eleven bits are sent for each byte (1 start bit, 8 data bits, 1 parity bit
and 1 stop bit). The PS/2 mouse sends on the order of 1,200 bits per
second. That allows it to report mouse position to the computer at a
maximum rate of about 40 reports per second. If you are moving the
mouse very rapidly, the mouse may travel an inch or more in onefortieth of a second. This is why there is a byte allocated for X and Y
motion in the data protocol.
Pins:
1. Unused
2. +5 volts (to
power the
chip and
LEDs)
3. Unused
4. Clock
5. Ground
6. Data
Optical Readers
• Convert printed or hand written information to computer
data
• Information is read in one two ways
– OCR (Optical Character Recognition)
• Printed or typewritten characters
• Handwritten characters
– OMR (Optical Mark Readers)
marks which are placed in predefined areas of the document
• Pre-printed paper is normally used for hand-printed marks or characters
• Readers are designed to read marks or characters positioned in a matrix
pattern
• Colored printing is used in pre-printing, which is insensitive to the reader
OCR devices
• OCR is the scanning of text documents into graphic images,
then using software to decode the graphic picture elements
back into text.
• When the scanner scans the document, it is read as a series
of black and white pixel (dots) elements. This process often
tends to degrade the edges of the text characters, and is
more pronounced when the characters on the original are
too small. Edge degradations makes it harder for the OCR
software to convert the pixel elements back into text later
on.
• The OCR software reads the bitmap of pixels created in step
1 and averages out the white spaces on the page, effectively
identifying paragraphs and eliminating graphics. The white
spaces between each line of text is used as a baseline
reference for recognizing the characters on that line.
OCR devices
• First, the OCR software tries to match each character on a line in the
bitmap against character templates that it knows about.
• The remaining unidentified characters have a technique known as
feature extraction applied to them. The OCR software calculates the
characters height, lines, curves and other features. It can then make
close guesses as to the characters value.
• For the remaining characters the OCR software cannot recognize, the
software can either apply contextual analysis, which basically means
looking at the syntax and construction of the words and making a
guess (for example, changing thi5 to this), or give up and substitute
the unknown character with a distinctive symbol such as ~ or @.
• The finished information is normally able to be saved in a number of
different formats, text or Rich Text Format (RTF). OCR software
which support RTF can also recognize bold, italics, retain tabs and
whitespace, as well as recognize a limited number of different fonts.
Bar Codes
• Represents numeric data as a series of bars
• Bars have varying thickness and separations
• Numeric data is often written underneath the barcode
• Easily read by light-pen or scanner device
The light pen has a sensitive tip which contains a
light source and light detector. When the pen is
stroked along the bar-code symbol, the light from
the pen bounces off the dark bars to produce a
corresponding set of binary pulses. This sequence
is decoded to give the numeric data that the barcode represents
• Examples of Bar-Code Applications
–
–
–
–
Consumer goods (super-markets)
Stock inventory
Library systems for cataloging books
Drug dispensing at your local pharmacy
Card Readers
• Magnetic Card Readers
– Magnetic card swipe readers read the information
contained on a magnetic strip on a plastic card
• Smart Card Readers
– Smart cards are intelligent cards which replace the
magnetic stripe with a controller and memory
• Optical Card Readers
– Optical Smart Cards are the same size and shape as
standard plastic credit cards, but hold up to six
megabytes of updateable digital information in a secure,
inexpensive, and compact personal package
Magnetic Card Readers
•
Characteristics
– the data is stored on the magnetic stripe
– the number of characters stored is typically about 1K
– the card often includes a name and signature, or other details (like a photo) for added security
•
Connection
– The magnetic card reader is inserted between the keyboard and the base unit of the computer. The
magnetic card unit converts the information on the magnetic card and presents it to the computer as
a series of ASCII characters.
– The computer thinks that the characters came from the keyboard. This simplifies writing software to
read magnetic cards.
•
Applications
–
–
–
–
Electronic Funds Transfer, Point of Sale (EFT-POS)
Drivers License
Telecom Phone Cards
Credit Cards, VISA, MASTER-CARD, AMERICAN EXPRESS
Smart Card Readers
• Characteristics
–
–
–
–
include built-in electronics and memory storage (often 16KB or more)
logs details and transaction information
numerous applications, including shopping, banking, SKY-TV, medical
potential security risks
• A scheme (1996) involved a medical center which placed customer
information on smart cards.
– This included medical and dentist information from the center. Even if cards are
protected by the use of PIN (Personal Identification Numbers) information,
which is normally limited to 4 digits, the potential for disaster is comparatively
high if someone has the time and resources to fraudulently obtain a card and
access the information on it for criminal reasons
Optical Cards
•
•
Optical Smart Cards are the same size and shape as standard plastic credit
cards, but hold up to six-megabytes of updateable digital information in a
secure, inexpensive, and compact personal package.
Data that can be stored on Optical Smart Cards include
–
–
–
–
–
–
•
Advantages of optical smart cards over chip and magnetic-stripe cards include:
–
–
–
–
–
–
–
•
cardholder name, address, and other personal information
digitized cardholder photographs
signatures
medical images or x-rays
updateable account balances and transaction audit trails
security information
Large storage capacity of six-megabytes
Off-Line card verification with NO dependence on telephone or other links to a
central database
Faster card updates (30 times faster than chip-cards)
Permanent and VERY secure fraud-proof operation using the latest crypto
technology
No possible data loss from exposure of cards to static electricity, water, magnetic or
electrical fields, or to x-rays (for example -- during airport security checks)
Less expensive long-term system operating costs
Global card standards with multiple sources
The Canadian Government has adopted the Canon Optical Card as a positive
identification card-"CANPASS" for international travelers. The CANPASS
Card contains traveler's photo and fingerprint templates and reduces the time
required to clear Customs by about 80%.
Printers
• There are several major printer technologies available. These
technologies can be broken down into two main categories with
several types in each:
• Impact - These printers have a mechanism that touches the paper in
order to create an image:
– Dot matrix printers use a series of small pins to strike a ribbon coated with ink,
causing the ink to transfer to the paper at the point of impact
– Character printers are basically computerized typewriters. They have a ball or
series of bars with actual characters (letters and numbers) embossed on the
surface. The appropriate character is struck against the ink ribbon, transferring
the character's image to the paper. Character printers are fast and sharp for basic
text, but very limited for other use.
• Non-impact - These printers do not touch the paper when creating an
image. Inkjet printers are part of this group, which includes:
– Inkjet printers, use a series of nozzles to spray drops of ink directly on the paper
– Laser printers, use dry ink (toner), static electricity, and heat to place and bond
the ink onto the paper
Inkjet Printer Components
• Print head assembly
– Print head - The core of an inkjet printer, the print head contains a series of nozzles that
are used to spray drops of ink
• Ink cartridges
– Depending on the manufacturer and model of the printer, ink cartridges come in various
combinations
• separate black and color cartridges
• color and black in a single cartridge or even a cartridge for each ink color. The cartridges of
some inkjet printers include the print head itself
• Print head stepper motor - A stepper motor moves the print head assembly (print
head and ink cartridges) back and forth across the paper
– Some printers have another stepper motor to park the print head assembly when the
printer is not in use. Parking means that the print head assembly is restricted from
accidentally moving, like a parking break on a car
• Belt - A belt is used to attach the print head assembly to the stepper motor.
• Stabilizer bar - The print head assembly uses a stabilizer bar to ensure that
movement is precise and controlled
Inkjet Printer Components
• Paper feed assembly
– Paper tray/feeder
• Most inkjet printers have a tray that you load the paper into.
• Some printers dispense with the standard tray for a feeder instead. The feeder
typically snaps open at an angle on the back of the printer, allowing you to place
paper in it. Feeders generally do not hold as much paper as a traditional paper tray.
– Rollers - A set of rollers pull the paper in from the tray or feeder and advance
the paper when the print head assembly is ready for another pass
– Paper feed stepper motor - This stepper motor powers the rollers to move the
paper in the exact increment needed to ensure a continuous image is printed
• Control circuitry - A small but sophisticated amount of circuitry is
built into the printer to control all the mechanical aspects of operation,
as well as decode the information sent to the printer from the
computer
• Interface –parallel port, USB (Universal Serial Bus) or sometimes
network technologies (wired or wireless)
Inkjet Printer Components
• Left – print head, belt and paper feed mechanisms
• Right – control circuitry
Inkjet Printers Technology
• Thermal bubble - Used by manufacturers such as Canon,
this method is commonly referred to as bubble jet
– tiny resistors create heat, and this heat vaporizes ink to create a
bubble. As the bubble expands, some of the ink is pushed out of a
nozzle onto the paper. When the bubble "pops" (collapses), a
vacuum is created. This pulls more ink into the print head from the
cartridge
– A typical bubble jet print head has 300 or 600 tiny nozzles, and all
of them can fire a droplet simultaneously
• Piezoelectric – Epson patent, this technology uses piezo
crystals
– A crystal is located at the back of the ink reservoir of each nozzle.
The crystal receives a tiny electric charge that causes it to vibrate.
When the crystal vibrates inward, expanding, it forces a tiny
amount of ink out of the nozzle. When it vibrates out, it pulls some
more ink from the reservoir to replace the ink sprayed out
Inkjet Printer Technology
Piezo Transducer
driver
Heating element
To reservoir
ink
To reservoir
ink
Bubble
Nozzle
Piezoelectric head
Nozzle
Bubble jet head
Laser Printer
• The primary principle at work in a laser printer is static
electricity, the same energy that makes clothes in the dryer
stick together or a lightning bolt travel from a thundercloud
to the ground.
• Static electricity is simply an electrical charge built up on an
insulated object, such as a balloon or your body. Since
oppositely charged atoms are attracted to each other, objects
with opposite static electricity fields cling together.
• A laser printer uses this phenomenon as a sort of "temporary
glue." The core component of this system is the
photoreceptor, typically a revolving drum or cylinder. This
drum assembly is made out of highly photoconductive
material that is discharged by light photons.
Laser Printer
Finally,
With
Initially,
thethe
powder
the
printer
drum
pattern
passes
is is
given
affixed,
theathe
paper
total
the
positive
through
drum rolls
charge
the over
fuser,
a drum
sheet
athe
pair
charge
of
of
paper,
heated
corona
which
rollers.
wire,
is As
moving
a the
wire
After
the
pattern
set,
printer
coats
theby
with
positively
along
paper
with passes
aanbelt
electrical
below.
through
current
Before
these the
running
rollers,
paperthe
through
rolls
loose
under
it.
toner
(Some
thepowder
drum,
printers
it
melts,
isuse
fusing
a charged
a negative
with roller
thecharge
fibers
charged
toner
-a fine,
black
powder.
Since
it has
agiven
positive
charge,
the
byinstead
in
the
thepaper.
transfer
of aThe
corona
corona
fuser
wire,
rolls
wire
but
the
(charged
the
paper
principle
to
roller).
the is
output
This
the same.)
charge
tray, and
Asis the
you
stronger
drum
havethan
revolves,
yourthe
finished
negative
the
toner
clings
to
the
negative
discharged
areas
of
the
drum,
but
not
the
charge
page.
printer
The
ofshines
the
fuser
electrostatic
aalso
tinyheats
laserimage,
up
beam
the across
paper
so theitself,
the
paper
surface
of
can
course,
pull
to discharge
the
which
toneriscertain
powder
why pages
points.
away.
areSince
Into
always
this
it
charged
"background."
This
like
writing
on
ispositively
hot
way,
moving
when
thethey
laser
at the
come
"draws"
sameout
speed
the
of aletters
as
laser
theprinter
and
drum,
images
the
or
photocopier;
paper
toisbesomething
picks
printed
up
After
as
theadepositing
image
pattern
pattern
of toner
electrical
exactly.
on athe
Tosoda
paper,
charges
keep
the
the
--drum
an
paper
electrostatic
surface
from
passes
the
to discharge
the
The
drum,
system
iscan
discharged
also
This
work
bright
bywith
light
the The
detac
the
exposes
charges
corona
the
reversed
entire
wire
can
with
gluesticking
andimage.
then
rolling
ititlamp.
over
some
flour:
flour
only
immediately
photoreceptor
-that is,
positive
after
surface,
picking
electrostatic
erasing
up the
the
toner.
image
electrical
on aimage.
negative
background
drum
thenapasses
the
sticks
toathe
glue-coated
part
of the
can,
soThe
you
endsurface
up with
message
charge corona wire, which reapplies the positive charge
written in powder.
Laser Printer Controller
• Before a laser printer can do anything else, it needs to receive the page data and
figure out how it's going to put everything on the paper. This is the job of the
printer controller.
• The printer controller is the laser printer's main onboard computer. It talks to the
host computer through a communications port, such as a parallel port or USB port.
At the start of the printing job, the laser printer establishes with the host computer
how they will exchange data. The controller may have to start and stop the host
computer periodically to process the information it has received
• In an office, a laser printer will probably be connected to several separate host
computers, so multiple users can print documents from their machine. The controller
handles each one separately, but may be carrying on many "conversations"
concurrently. This ability to handle several jobs at once is one of the reasons why
laser printers are so popular
• For the printer controller and the host computer to communicate, they need to speak
the same page description language. In earlier printers, the computer sent a special
sort of text file and a simple code giving the printer some basic formatting
information. Since these early printers had only a few fonts, this was a very
straightforward process. Today there are hundreds of different fonts to choose from,
as well as complex graphics. To handle all of this diverse information, the printer
needs to speak a more advanced language
Laser Printer Controller
•
The primary printer languages these days are Hewlett Packard's Printer Command
Language (PCL) and Adobe's Postscript. Both of these languages describe the page in
vector form
– that is, as mathematical values of geometric shapes, rather than as a series of dots (a bitmap image).
•
•
The printer itself takes the vector images and converts them into a bitmap page. With this
system, the printer can receive elaborate, complex pages, featuring any sort of font or image.
Also, since the printer creates the bitmap image itself, it can use its maximum printer
resolution.
Some printers use a graphical device interface (GDI) format instead of a standard PCL. In
this system, the host computer creates the dot array itself, so the controller doesn't have to
process anything
– it just sends the dot instructions on to the laser.
•
But in most laser printers, the controller must organize all of the data it receives from the host
computer. This includes all of the commands that tell the printer what to do
–
•
•
what paper to use, how to format the page, how to handle the font, etc. For the controller to work
with this data, it has to get it in the right order.
Once the data is structured, the controller begins putting the page together. It sets the text
margins, arranges the words and places any graphics. When the page is arranged, the raster
image processor (RIP) takes the page data, either as a whole or piece by piece, and breaks it
down into an array of tiny dots. The printer needs the page in this form so the laser can write
it out on the photoreceptor drum.
In most laser printers, the controller saves all print-job data in its own memory. This lets the
controller put different printing jobs into a queue so it can work through them one at a time.
It also saves time when printing multiple copies of a document
Laser Printer Assembly
• The laser part of a laser printer is made out of:
– A laser
– A movable mirror
– A lens
•
The laser receives the page data (the tiny dots that make up the text
and images) one horizontal line at a time. As the beam moves across
the drum, the laser emits a pulse of light for every dot to be printed,
and no pulse for every dot of empty space. The laser doesn't actually
move the beam itself. It bounces the beam off a movable mirror
instead. As the mirror moves, it shines the beam through a series of
lenses. This system compensates for the image distortion caused by
the varying distance between the mirror and points along the drum.
• The laser assembly moves in only one plane, horizontally. After each
horizontal scan, the printer moves the photoreceptor drum up a notch
so the laser assembly can draw the next line. A small print-engine
computer synchronizes all of this perfectly, even at high speeds.
Advantages of Laser Printers
• The main advantages of laser printers are speed, precision and
economy. A laser can move very quickly, so it can "write" with much
greater speed than an ink jet. And because the laser beam has an
unvarying diameter, it can draw more precisely, without spilling any
excess ink. Laser printers tend to be more expensive than inkjet
printers, but it doesn't cost as much to keep them running
– toner powder is cheap and lasts a long time, while you can use up expensive ink
cartridges very quickly. This is why offices typically use a laser printer.
– When they were first introduced, laser printers were too expensive to use as a
personal printer. Since that time, however, laser printers have gotten much more
affordable. Now you can pick up a basic model for just a little bit more than a
nice inkjet printer.
• As technology advances, laser-printer prices should continue to drop,
while performance improves. We'll also see a number of innovative
design variations, and possibly brand-new applications of electrostatic
printing. Many inventors believe we've only scratched the surface of
what we can do with simple static electricity!
Other Printers
• Solid ink printers contain sticks of wax-like ink that are melted and applied to the
paper. The ink then hardens in place.
• Dye sublimation printers have a long roll of transparent film that resembles sheets
of red-, blue-, yellow- and gray-colored cellophane stuck together end to end.
Embedded in this film are solid dyes corresponding to the four basic colors used in
printing: cyan, magenta, yellow and black (CMYK). The print head uses a heating
element that varies in temperature, depending on the amount of a particular color
that needs to be applied. The dyes vaporize and permeate the glossy surface of the
paper before they return to solid form. The printer does a complete pass over the
paper for each of the basic colors, gradually building the image.
• Thermal wax printers are something of a hybrid of dye-sublimation and solid ink
technologies. They use a ribbon with alternating CMYK color bands. The ribbon
passes in front of a print head that has a series of tiny heated pins. The pins cause the
wax to melt and adhere to the paper, where it hardens in place.
• Thermal auto chrome printers have the color in the paper instead of in the printer.
There are three layers (cyan, magenta and yellow) in the paper, and each layer is
activated by the application of a specific amount of heat. The print head has a
heating element that can vary in temperature. The print head passes over the paper
three times, providing the appropriate temperature for each color layer as needed
The Monitor
• Often referred to as a monitor when packaged in a separate case, the display is the
most-used output device on a computer. The display provides instant feedback by
showing you text and graphic images as you work or play.
• Display technologies:
– Desktops were usually using Cathode Ray Tube (CRT) display.
– Portable computing devices such as laptops incorporate Liquid Crystal Dispay (LCD),
light-emitting diode (LED), gas plasma or other image projection technology.
• Because of their slimmer design and smaller energy consumption, monitors
using LCD technologies are beginning to replace the venerable CRT on
many desktops.
• Main characteristics of a monitor are:
– Display technology - Currently, the choices are mainly between CRT and LCD
technologies (more LCD than CRT).
– Viewable area (usually measured diagonally)
– Aspect ratio and orientation (landscape or portrait)
– Maximum resolution
– Dot pitch
– Refresh rate
– Color depth
– Amount of power consumption
Display Technology
•
•
•
•
•
•
•
Displays have come a long way since the blinking green monitors in text-based computer
systems of the 1970s.
In 1981, IBM introduced the Color Graphics Adapter (CGA), which was capable of rendering
four colors, and had a maximum resolution of 320 pixels horizontally by 200 pixels
vertically.
IBM introduced the Enhanced Graphics Adapter (EGA) display in 1984. EGA allowed up to
16 different colors and increased the resolution to 640x350 pixels, improving the appearance
of the display and making it easier to read text.
In 1987, IBM introduced the Video Graphics Array (VGA) display system. Most computers
today support the VGA standard and many VGA monitors are still in use (640x480)
IBM introduced the Extended Graphics Array (XGA) display in 1990, offering 800x600 pixel
resolution in true color (16.8 million colors) and 1,024x768 resolution in 65,536 colors.
Most displays sold today support the Ultra Extended Graphics Array (UXGA) standard.
UXGA can support a palette of up to 16.8 million colors and resolutions of up to 1600x1200
pixels, depending on the video memory of the graphics card in your computer.
A typical UXGA adapter takes the digital data sent by application programs, stores it in video
random access memory (VRAM) or some equivalent, and uses a digital-to-analog converter
(DAC) to convert it to analog data for the display scanning mechanism. Once it is in analog
form, the information is sent to the monitor through a VGA cable.
Display Characteristics
• Viewable area
– Aspect ratio: typical 4:3 or 16:9
– Screen size: 15, 17, 19, 21, 22, 24, 26, etc…
• Resolution
– refers to the number of individual dots, known as pixels, contained on a display.
Resolution is expressed by identifying the number of pixels on the horizontal axis (rows)
and the number on the vertical axis (columns), such as 640x480. The monitor's viewable
area, refresh rate and dot pitch all directly affect the maximum resolution a monitor can
display
• Dot Pitch
– is the measure of how much space there is between a display's pixels. When considering
dot pitch, remember that smaller is better. Packing the pixels closer together is
fundamental to achieving higher resolutions
• Refresh Rate
– In monitors based on CRT, is the number of times that the image on the display is drawn
each second. If your CRT monitor has a refresh rate of 72 Hertz (Hz), then it cycles
through all the pixels from top to bottom 72 times a second. Refresh rates are very
important because they control flicker, and you want the refresh rate as high as possible.
Too few cycles per second and you will notice a flickering, which can lead to headaches
and eye strain.
Display Characteristics
• Color depth
– The combination of the display modes supported by your graphics adapter and
the color capability of your monitor determine how many colors can be
displayed.
• For example, a display that can operate in SuperVGA (SVGA) mode can display up
to 16,777,216 (usually rounded to 16.8 million) colors because it can process a 24bit-long description of a pixel. The number of bits used to describe a pixel is known
as its bit depth.
– With a 24-bit bit depth, 8 bits are dedicated to each of the three additive primary
colors (red, green and blue).
• This bit depth is also called true color because it can produce the 10,000,000 colors
discernible to the human eye, while a 16-bit display is only capable of producing
65,536 colors. Displays jumped from 16-bit color to 24-bit color because working in
8-bit increments makes things a whole lot easier for developers and programmers.
• Power consumption
– varies greatly with different technologies. CRTs are somewhat power-hungry, at
about 110 watts for a typical display, especially when compared to LCDs, which
average between 30 and 40 watts.
CRT
•
•
•
•
•
•
the CRT consists of a vacuum tube
enclosed in glass. At the end of the tube is
an electron gun (which generates an
electron beam), focusing and deflection
assembly. At the other end of the tube is
the screen surface which is coated in
phosphorous which emits a dot of light
when struck by the electronic beam.
the electron gun emits a high stream of
electrons.
the electron beam is deflected by signals
applied to the deflection assembly.
when the electron beam strikes the
phosphorous coating on the inner surface
of the screen, light is emitted.
the electron beam is swept across the
screen from left to right in horizontal lines,
from top to bottom, in a pattern called a
raster.
the screen image is repeated at the refresh
rate, as the image dissipates quickly.
CRT
•
color systems use three electron beams,
one each for red, blue and green.
in color systems, three different phosphors
are used which match each of the three
beams. This collection of three phosphors
is called a triad.
a shadow mask is used to prevent the
beams from striking the wrong phosphors
•
•
•
Interlaced Displays
–
–
–
–
the screen picture is made up of two full passes of the electron beam from top to bottom
the first pass builds up one screen doing only odd line numbers
the second pass completes the screen doing all the even line numbers
the technique relies upon the persistence of the image on the screen so that the human eye blends
both passes together. Persistence is a measure of how long the image remains on the screen before it
fades away. This is because phosphor only emits light when struck by electrons, when it stops being
struck, it stops emitting light.
– this technique is commonly used for Television
•
Non-Interlaced Displays
– In non-interlaced displays, the screen picture is made from one single pass of the electron beam
from top to bottom.