Coolants

Transcript Coolants

Coolants

Tom Birch Jim Halderman 1 1

Introductions: Tom Birch

• Retired instructor from Yuba College, Marysville, CA. • Author of many automotive textbooks • Former officer in CAT and NACAT Board Member 2

Jim Halderman

 Former flat-rate technician and instructor and a business owner. Author of many automotive books and lives in Dayton, Ohio.

 http://jameshalderman.com

Topics to be Discussed

  Engine coolants Water Purpose and function (1/2 of the coolant)  Coolant Types  Cooling system testing  Cooling system service 4

What is Coolant?

Coolant is a mixture of: 1. Water (50%) 2. Anti-Freeze (ethylene glycol-about 93%) 3. Corrosion inhibitors (additives) Additives: About 3% Water: 50% Ethylene Glycol: 47% Coolant Need to know 55

Water

Water is the principal ingredient and: 1. Is inexpensive 2. Is a very efficient heat exchange fluid 3. Has excellent thermal conductivity 4. Has a good specific heat 5. Freezes at 32°F (0°C) 6. Boils at 212°F (100°C) The water used in coolant must be clean & pure.

Need to know 66

Good Water

The American Society for Testing and Materials (ASTM) standards for water quality include: Chloride <40 ppm Sulfate <100 ppm Calcium <100 ppm Magnesium <100 ppm Total Hardness <170 ppm pH Range: 5.5—9.0 Iron <1 ppm Nice to know 77

Freeze and Boil

Freezing Point Boiling Point Pure Water 0° C (32° F) 50/50 Anti Freeze/Water -37° C (-35° F) 100° C (212° F) 106° C (223° F) 70/30 Anti Freeze/Water -55° C (-67° F) 113° C (235° F)

88 Need to know

Ethylene Glycol (EG)

Ethylene glycol is the base antifreeze used in every OEM factory fill. The additive package will vary.

Need to know 9

Propylene Glycol (PG)

• Only sold to the aftermarket • Not recommended for use by vehicle manufacturers • More expensive than EG, Increased cost is $/gallon • Still toxic but is not as sweet as EG Need to know 10

Embittered Coolant

Embittered = tastes awful Embittering agent is required (denatonium benzoate, 30 ppm) Required in California and Oregon since 2004 but not included on the label.

Need to know 11

Bittered States

At this time, 7/20/10, 12 states require antifreeze with a bittering agent: dentonium benzoate. They are: • Arizona • New Mexico • Virginia • California • Maine • New Jersey • Oregon • Tennessee • Utah • Vermont • Washington • Wisconsin 4 states: Illinois, Massachusetts, New Hampshire, and Ohio are working on a similar rule.

OAT

=

DEX-COOL

is one brand

Nice to know 13

HOAT=

Red

;

Pink

; Yellow or

Blue Nice to know 14

Need to know

Replacement Antifreeze

The best choice is to follow the vehicle manufacturer’s recommendations . OR, you can follow the recommendations of reliable antifreeze manufacturers (next slide).

•

Coolant Summary

Ethylene glycol

- Most ethylene glycol coolant is

any color

and contains about 93% ethylene glycol plus water and additives.

• • • •

Propylene glycol

- less harmful to pets and animals because it is not sweet tasting, although it is still harmful if swallowed.

Organic acid technology

(

OAT

) antifreeze coolant – This type is ethylene glycol based but it does not contain silicates or phosphates. It is usually

orange.

DEXCOOL is an OAT coolant.

Hybrid organic acid technology

silicate) (

HOAT

) – This

orange, green, red, blue or yellow

coolant is an ethylene glycol based coolant similar to the OAT- type antifreeze as it uses additives (a low amount of • • • • •

VW/Audi pink

- Most of these coolants are HOAT (ethylene glycol-based with some silicate and contain an organic acid) and are phosphate free.

Asian red

– This coolant is ethylene glycol-based and is silicate-free, yet contains phosphate.

Mercedes and Ford yellow

and no phosphates.

– This conventional ethylene glycol coolant has low amounts of silicate

Mercedes Lifetime – Very expensive, can be drained, filtered and reused.

Korean

European blue

– This conventional ethylene glycol coolant has low amounts of silicate and no phosphates.

Nice to know 16

pH Tests

pH can be measure using test strips or a meter. Fairly accurate and costs pennies/test.

Need to know 17

Metal Corrosion

This iron tube has been ruined by rust.

Need to know 18

Diesel Wet Sleeve Cavitation

The sleeve can vibrate during the combustion stroke producing the pressure drop, bubbles, and metal erosion. Heavy duty coolants contain supplemental coolant additives (SCA) to help prevent this.

Need to know 19

Bi-Metal Corrosion

Ions move from more active metals to less active metal through the coolant which acts like the electrolyte Nice to know 20

Radiator Voltage

Connect the negative voltmeter lead to a good ground (this radiator has a plastic filler neck), and immerse the positive lead into the coolant. A reading of 0.300 V or greater indicates corrosion is probably occurring.

Need to know 21

Refractometer Image

Shadow Read Here The image will show the amount of freeze protection and is read at the scale at the bottom edge of the shadow. This unit can check EG and PG antifreeze freeze protection and battery specific gravity.

Need to know 22

Universal Coolant

• Arctic Blend • Recycool •Prestone Prime coolants that have been formulated to be used in any vehicle Nice to know 23

Need to know

Additives

The major additives: 1. Reduce corrosion 2. Buffer (control) pH 3. Add color (dye)

IAT

Inorganic Additive Technology (IAT) changed regularly. is the traditional green coolant used in most older vehicles. This solution offers fast-acting corrosion protection, but the additives are quickly consumed, exposing the cooling system to possible corrosion problems if not Need to know

IAT

(Usually Green in Color)

• • • Inorganic Additive Technology (IAT) antifreeze can contain: Silicates (possible abrasive dropouts) Phosphates Borates IAT is considered obsolete and can cause early failure of ceramic-phenolic seals used in newer water pumps.

Need to know

OAT (Usually Orange)

Organic Acid Technology (OAT) is the formula found in DEX-COOL®, and is usually the antifreeze/coolant of choice for GM, VW, and many Japanese/Asian vehicles. This formula is engineered to offer long-life corrosion protection.

The downside of OAT is it is coolant (IAT and HOAT). In fact, Ford, Chrysler and others say to not not compatible with other types of use this type of coolant in their newer models. Need to know

OAT

-continued NAPS =nitrates, amines, phosphate and silicate free Nice to know 28

OAT

=

DEX-COOL

is one brand

Nice to know 29

DEX-COOL

Concerns

• Root cause = air entering system • Check cap replace cap • Air causes ‘ Brown Gunk’ • Rust then causes blockages Need to know 30

Rust in Engine

• DEX-COOL or DEX-COOL + Air= rust + core sand = Brown gunk Need to know 31

GM

DEX-COOL

Problems

 Class action suit; GM may have to pay for intake gaskets on V-6s (V-8s still being determined) Brown Gunk on radiator cap Need to know 32

DEX-COOL ’s Unique Formulation

• DEX-COOL uses Ethylhexanoic Acid (2 EH) as a corrosive inhibitor • 2-EH is prone to damage plastics like Nylon 6.6 used in intake manifold gaskets and radiators • G30 OAT and Peak Global OAT do NOT use 2-EH Nice to know 33

HOAT

( Many

colors

) Hybrid Organic Acid Technology (HOAT) long-life coolant. is found in newer Ford, Chrysler and Mercedes vehicles. Said to use the very best aspects of both IAT and OAT, HOAT is a very protective, Need to know

HOAT=

Red

;

Pink

; Yellow or

Blue Nice to know 35

POAT Coolant

• Phosphated Organic Acid Technology (POAT) • Dark Green in color • Used in Mazda-based Fords (2008+) • same as Mazda FL 22 • $34.95 per gallon

Ford Motor Company & E-OAT

The E = European, low silicate and phosphate free •Ford of Europe has validated Dex-Cool and uses it with no problems. •Ford of U.S. has reengineered all of their new engines (No- Cavitation water pumps and no-silicone rubber or Nylon 66) to work with this formula.

Ford/Mercury Coolant

Pre 1999 99 —01 2002 2003 2004 The 1999 —2001 Cougar used a OAT Dex-Cool clone, but had issues with water pump cavitation.

Dex-Cool & OAT that meets GM Spec.

Prestone markets an OAT antifreeze (Extended Life) “compatible with ANY antifreeze/ coolant”) that meets the GM Dex-Cool spec.

it is less expensive than Dex-Cool-labeled products because of no-royalty cost. 39

Passivation

• Passivation = is a chemical reaction the takes place between coolant additives and the metal that it protects • Takes a few days or few weeks • It creates barrier between the metal and corrosion • Each chemical package does its own passivation • if you change chemical packages, passivation has to start over • It boils down to: DO NOT CHANGE PACKAGES .

Nice to know 40

“G” Designations

• G = Glysantin –trade name of BASF. Valvoline (Zerex) in the US.

• G30 , G33, G34 = non-silicate and phosphate free (DEX-COOL replacement) • G05 = Phosphate free-low silicates (Asian formula and Chrysler HOAT) 41 Nice to know

“G” Designations-

continued • G11 =Blue VW used before 1997 • G12 =Pink/Red VW 1997+ • G12 =Purple VW 2003+ • HOAT formulation; phosphate free 42

“G” Designations-

continued • G48 =Low Silicate and Phosphate free • Blue Color • NAP =nitrates, amines, phosphate free • BMW 43

Need to know

Replacement Antifreeze

The best choice is to follow the vehicle manufacturer’s recommendations . OR, you can follow the recommendations of reliable antifreeze manufacturers (next slide).

Need to know

Color

The color helps us identify a coolant leak. It also helps us identify the additive package.

Should green not be used as an indicator what to use-some Chrysler vehicles used HOAT coolant that was

•

Coolant Summary

Ethylene glycol

- Most ethylene glycol coolant is

any color

and contains about 93% ethylene glycol plus water and additives.

• • • •

Propylene glycol

- less harmful to pets and animals because it is not sweet tasting, although it is still harmful if swallowed.

Organic acid technology

(

OAT

) antifreeze coolant – This type is ethylene glycol based but it does not contain silicates or phosphates. It is usually

orange.

DEXCOOL is an OAT coolant.

Hybrid organic acid technology

silicate) (

HOAT

) – This

orange, green, red, blue or yellow

coolant is an ethylene glycol based coolant similar to the OAT- type antifreeze as it uses additives (a low amount of • • • • •

VW/Audi pink

- Most of these coolants are HOAT (ethylene glycol-based with some silicate and contain an organic acid) and are phosphate free.

Asian red

– This coolant is ethylene glycol-based and is silicate-free, yet contains phosphate.

Mercedes and Ford yellow

and no phosphates.

– This conventional ethylene glycol coolant has low amounts of silicate

Mercedes Lifetime – Very expensive, can be drained, filtered and reused.

Korean

European blue

– This conventional ethylene glycol coolant has low amounts of silicate and no phosphates.

Nice to know 47

Depletion Rate of Additives

Need to know 48

pH

Acid

pH is a measure of acidity or alkalinity of a solution. Less than 7 is considered acidic. Greater than 7 is considered alkaline.

Alkaline Substance pH

Hydrochloric acid Battery acid Lemon juice Cola -1.0

0.5

2.4

2.5

Vinegar 2.9

Orange or Apple juice 3.5

Acid Rain Tea or healthy skin Milk Pure water <5.0

5.5

6.5

7.0

Healthy human saliva 6.5 – 7.4

Blood 7.34 – 7.45

Sea water Hand soap Household ammonia 7.7 – 8.3

9.0 – 10.0

11.5

Bleach Household lye Caustic Soda 12.5

13.5

13.9

Nice to know

pH Effects

Fresh antifreeze pH = 9 and 11 Used coolant pH = 7.5 and 10 It can also increase electrolysis ( the dissimilar metals in contact with an electrolyte can produce a simple battery) Need to know

pH of various coolants

• IAT = 9.0-10.5 new • OAT = 7.5-8.5 new (G30 and G34 designation) • HOAT = 7.5-8.5 new (G05,G48,G11 or G12 designation) Need to know 51

Need to know

Desired pH

pH Tests

pH can be measure using test strips or a meter. Fairly accurate and costs pennies/test.

Need to know 53

pH Meter

This Milwaukee is probably more accurate and cost $30.00.

Need to know 54

Corrosion

Corrosion is the “ decomposition of metal ” (called rust or aluminum oxide, the whitish material that forms on aluminum components) Oxide formation: 1. eats away at the parent material from the outside 2. forms an insulating barrier for heat transfer Need to know

Metal Corrosion

This iron tube has been ruined by rust.

Need to know 56

Corrosion

aluminum oxide, often found on coolant outlet/stat cover Need to know

Corroded Water Pump

Need to know One of the reasons for the removal of silicates from coolant 58

Corroded pump can cause:

• reduced coolant flow and an overheating condition Need to know 59

Cavitation

Cavitation Cavitation is the sudden formation and collapse of low pressure bubbles. With gasoline engines, the pressure drop can occur at the inlet of the water pump. These bubbles produce a pitting of the solid metal .

Need to know

Cavitation Damage

The very low pressure can produce gas bubbles that implode next to a metal surface. The implosion blasts particles from the surface.

Need to know 61

Diesel Wet Sleeve Cavitation

The sleeve can vibrate during the combustion stroke producing the pressure drop, bubbles, and metal erosion. Heavy duty coolants contain supplemental coolant additives (SCA) to help prevent this.

Need to know 62

Galvanic action

• Galvanic activity does not require an outside source of voltage • The higher the conductivity of the coolant, the greater the amount of corrosion Need to know 63

Metals

Nice to know 64

Bi-Metal Corrosion

Ions move from more active metals to less active metal through the coolant which acts like the electrolyte Nice to know 65

Electrolysis

Electrolysis requires the use of an outside voltage source.

•When electrical ions move from metal to the coolant, they can take metal atoms with them • This metal transfer can eat holes in a heater core or radiator. •Electrolysis holes will usually start from the inside and have a dark coloration. Need to know

Testing Coolant with a Voltmeter

• This test gives variable and questionable results depending on many factors • Galvanic =less than 200 mV • Electrolysis= (engine running and accessories switched on and off)=less than 300 mV. This check can locate faulty ground connections Need to know 67

Radiator Voltage

Need to know 68

Coolant Condition

This “green” antifreeze has a clean, bright appearance. The other types will have a different color but should also appear clean and bright.

A muddy brown or rust-reddish color indicates that corrosion is occurring.

Need to know 69

Freeze Protection, Refractometer

A few drops of coolant are placed under the sample window. The technician then holds the unit up to light and looks through the eye piece (right end).

Sample Window Eye Piece

Need to know 70

Refractometer Image

Need to know 71

Freeze Protection, Test Strips

Test strips will change color when they are dipped into the coolant, and the color change is compared to the container. Test strips are fairly accurate, easy to use, and inexpensive.

Need to know

Coolant Corrosion Protection

The new test strip color is compared to the color pads on the container to determine the amount of freeze protection and corrosion protection.

Need to know 73

Coolant Replacement

1. 15 to 20% remains in the system after it has been drained 2. Fill system with antifreeze first and top off with water 3. Be sure to use the specified coolant (GM warns not to reuse coolant drained from the system) (Mercedes has a lifetime coolant, drain, filter, & reuse) Need to know 74

Coolant Replacement-

#2 • Check the pressure cap and radiator for faults • Check all hoses and always use coolant hose Need to know 75

Universal Coolant

• Universal Gold =HOAT, extended life, low silicate, phosphate-free antifreeze/coolant.

• This product meets Ford WSS M97B51-A1 and Chrysler MS 9769 and other "global antifreeze" type specifications, as well as ASTM D3306, D4985 and D6210/11 Nice to know 76

Universal Coolant

• Arctic Blend • Recycool •Prestone Prime coolants that have been formulated to be used in any vehicle Nice to know 77

Coolant Recovery and Storage

Some shops recycle used antifreeze Should be stored until picked up for recycling Notice double containers to help avoid spills Need to know 78

Flushing a Dirty System

1. Drain system 2. Fill system with clean water & chemical 3. Run system to operating temp. (Heater on) 4. Drain system & fill with clean water 5. Repeat until drain water runs clear Any remaining flush agent will upset pH.

6. Fill system with 50/50 antifreeze/water mix 7. Run system to operating temp. (Heater on) 8. Adjust coolant level Caution: If flushing a really dirty system, be prepared to repair some leaks.

Need to know 79

Flushing

Some communities permit draining into sewer. EG and PG will biodegrade. There is a problem however if coolant is spilled on open ground.

Need to know 80

Be sure to clean the overflow/surge tank

It should empty if you start draining with the cap in place.

Need to know 81

Mix Coolant 50/50 or use premix

Coolant Exchange Machine

Most shops use machines like this.

Coolant drains have become fragile and hard to find.

83 Need to know

TECH TIP

• Check the freezing Point after service • Should be 34 degrees F (proper 50/50 mix) • If higher (i.e. -20 F) this means that there is too much water.

• If lower (i.e. -40 F) this means that there is too much antifreeze

Always check or replace the radiator pressure cap

The cap can be located on 1. the radiator 2. The coolant recovery reservoir 3. The upper radiator hose Note the pressure.

Need to know 85

Cap has two seals

Upper Seal Filler Neck Lower Seal To CRR

What will happen if the upper seal fails? What will happen if the lower seal fails?

Need to know 86

Never open when hot!

1 psi will increase the coolant boiling point 2.7

o F. A 15 lb. Cap will increase the BP 40.5

o F.

What can happen if the cap is removed from a hot system?

Need to know 87

Proper Fill

All of the air must be removed from the cooling system by one of these methods: • Bleeder screw : lets air escape • Air Lift : evacuates system before fill • Spill-Free Funnel : Lisle #22150 • Fluid Exchange : requires special equipment Need to know 88

Bleeder Valves

• Use a clear hose attached to the bleeder valve and the other end in a “suitable” container • Prevents coolant from getting on the engine and gives the technician a visual clue as to color of coolant Need to know 89

Leak Detection

A good system holds pressure Tracer dye and some antifreezes glow under UV light Need to know 90

What should Technician's do?

• Check service information for the designated coolant and replacement interval • Check the coolant appearance and level at every service • Check the pressure cap appearance at every service • Check the appearance and pH for signs that the coolant should be replaced before the regular service interval • Check Freeze Point, pH, and Galvanic/Electrolysis Need to know 91

Typical Questions/Answers

1. Are all green antifreezes the same?

A. No-Chrysler used HOAT coolant that was green like IAT coolant 2. Can DEX-COOL be replaced with conventional green coolant?

A. Yes, but then the coolant has be replaced every 24 months or 24,000 miles 92

Questions/Answers

3. Can coolants be mixed?

A. No 4. Is DEX-COOL propylene glycol ?

A. No. DEX-COOL and all other coolants are ethylene glycol except one labeled propylene glycol and is never used from the factory 93

Summary

• Not all coolants are the same • Not all tap water is OK to use • Premixed coolant usually produces good results • Check the coolant freezing/boiling point • Check the coolant pH • Always check or replace the pressure cap, especially on DEX-COOL vehicles 94

Resource materials

Contact Information

Tom Birch http://tombirch.com

Jim Halderman [email protected]