Transcript Propulsion

Propulsion
Chapter 9
Powering of Ships - Historical
•
•
•
•
•
•
Oars
Sails
Jet (1661)
Steam driven side wheeler (1801 - 1850)
– Fulton’s Clermont for passenger service on Hudson River
– Savannah (1819), first American steamer to cross Atlantic, full rigged auxiliary
steam ship
– Scotia, built by Cunard, last side wheeler (1861)
Propeller
– First proposed in England by Hooke in 1680
– First steam driven boat in NY 1804, Colonel Stevens
– First successful application 1828 in Trieste, 60 ft boat, travelled at 6 knots
– First practical application 1836, Ericsson (American) and Smith (British)
Great Britain, first screw-propeller steamer to cross the Atlantic (1845)
Power Definition
•
•
•
•
Various types of marine engines are not rated on the same basis
Internal Combustion Engines – Brake Horsepower PB
– Power measured at the crankshaft coupling by means of a mechanical, hydraulic or
electrical brake. Determine by a shop test PB=2πQn/550 where Q=brake torque and n =
revolutions per second
Steam turbine – Shaft Horsepower PS
– Power transmitted through the shaft to the propeller
– Usually measured aboard ship as close to the propeller as possible by means of a
torsionmeter. The instrument measures the angle of twist between the two sections of
the shaft, which angle is directly proportional to the torque transmitted.
– Ps = (ds)4 * G * θ * n / (613,033 * Ls) , where ds = shaft diameter, G = shear modulus of
elasticity, θ = measured angle of twist in degrees, n = revolutions per second, Ls = length
of shaft over which θ is measured
Delivered Horsepower – PD
– The power actually delivered to propeller is actually somewhat less than measured by
the torsionmeter, as there is some power lost in the stern tube bearings and in any shaft
tunnel bearings between the sterntube and site of the torsionmeter
Power Definition
Effective Power = PE = RTV (power needed to overcome RT at velocity V)
Thrust Power = PT = TVA where T (thrust) is a measure of the useful output of the
propeller which is located in water moving at an average velocity called the
velocity of advance (VA)
Hull Efficiency = ηH = PE/PT = RTV / TVA
PD = Delivered Power = 2 π n QD, where QD is torque delivered to the propeller
Theory of Propeller Action
•
•
•
•
Propellers derive their propulsive thrust by accelerating the fluid in which they work.
Momentum Theory – “disk” is capable of imparting a sudden increase of pressure to the fluid
passing (axial direction) through it
Impulse Theory – assumes that the disk propeller is capable of accelerating the fluid both
axially and rotationally.
Blade Element Theory – blade is considered to made up of a number of separate blades
instead of a disk. These blades can then be divided into successive strips across the blade
from leading to trailing edge. The forces on each strip can then be evaluated from a
knowledge of the relative velocity of the strip to the water and the characteristics of the
section shape
• ηo = TVA / 2 π 𝑛 𝑄 - open water efficiency (testing propeller in open water)
Nomenclature
Blade extends from its “root” where it’s attached to the hub “tip” outmost extremity
When rotating, the blade edge cutting the water first is the “leading edge” “trailing edge” other edge
“face” of the propeller is seen from behind or aft, also called “pressure face or driving face”
“the back” the other blade surface
Other terms –
Cavitation – occurs when on the back or the suction side of the propeller blade, the
pressure becomes so low, that the water vaporizes at the low pressure point and vapor
filled bubbles form in the water locally “boiling” the water. Cavitation can cause erosion
and pitting of the blades and noise, also causes propeller efficiency to drop.
Wake – region of disturbed fluid behind a body that is moving through a fluid. Ship
propellers are located within the wake of the ships that they propel and the propeller’s
performance is influenced by the flow in which it operates.
Wake = V – VA , where V is the ship speed and VA is the speed of advance
Speed of Advance – is the velocity of the water passing through the propeller disk in the
absence of any influences of the propeller. In most cases the speed of advance (VA) is
less than the ship speed (V), because the ship hull forward of the propeller moves some
water with it.
Wake Fraction (w) – non dimensional expression of the wake or wake speed as a
fraction of ship speed
W = (V – VA) / V = (1 – VA) / V
Efficiencies
•
•
•
•
•
•
Behind Efficiency ηB = PT/PD = TVA/2πnQD
Open Water Efficiency ηo = TVA/2πnQo
Relative Rotative Efficiency ηR = ηB/ηo
Shaft Transmission Efficiency ηS = PD/PS
– Shaft power PS = 2πnQS
Propulsive Efficiency (PC) ηP = PE / PS
– Overall efficiency of ship propulsion
– ηP = PE/PT = PT/PD = PD/PS
– ηP = ηH x ηB x ηS = ηH x ηo x ηR x ηS
Quasi-propulsive efficiency
– ηD = PE/PD = ηH ηo ηR
– This efficiency represents how well the propeller is matched to the ship
Thrust Deduction –
Resistance force measured with model being towed
When self propelled, the thrust force produced must be sufficient to overcome
the ship resistance at the corresponding speed
Resistance of the self propelled ship greater then the towed vessel because the
high pressure system caused at the stern. These pressures are normal to the hull
and have components that act in the forward direction due to the shape of the
stern.
The propeller changes the flow of water around the stern by accelerating the
water. This reduces the beneficial high pressure around the stern.
Effect is defined as Thrust Deduction Fraction (t)
t = T – RT / T = 1 – RT / T where t = Thrust deduction fraction, T = propeller thrust,
RT = ship resistance or RT = T (1 – t) where (1 - t) is the Thrust deduction factor
Hull Interaction:
Wake
Region of disturbed fluid behind a body that’s moving through a fluid
Ship propellers are located within this wake and must be defined by the
designer
The ship hull forward of the propeller carries along water within the
boundary layer which helps to reduce the resistance, called positive wake
wake = V – VA or w = (V – VA) (wake fraction 1– w)
w = (1 - VA) / V or rewritten VA = V (1 – w)
Hull Efficiency - ηH = PE / PT ratio of effective power to the thrust power
Also written in terms of wake fraction and thrust deduction factor
ηH = RTV / TVA = (1 – t) / (1 – w)
Hull efficiency depends on the shape and fullness of the stern of the ship.
Ship and Propeller Together
Propellers must be designed for optimum performance considering the flow of
water around the hull since the propeller change the pressure distribution around the
stern thereby increasing the resistance of the propeller
Coefficients
•
•
Thrust Coefficient
– Propeller must deliver a large thrust for it’s size, referred to as “heavily loaded”
– Non-dimensional way of expressing the propeller output
– KT = T / ρ n D4
Torque Coefficient
– Represents the input (torque) to the propeller
– KQ = Q / ρ n D4
– Advance Coefficient
• Necessary to have kinematic similarity for testing model propellers and scaling to
full size propellers
• J = VA / nD = (P/D) (1 – sR)
• Since the pitch ratio is the same for geometrically similar propellers, equivalence of
their advance coefficients will assure equivalence of their slip ratios as well.
Potential Wake –
the pressure distribution around vessel moving through a fluid is always high around
the stern where the flow lines close in after passing around the body.
The velocity of the water in this region is slower than the velocity of the ship
Called Potential Wake and always positive in the stern
Frictional Wake
Within the viscous boundary layer, some water is carried in the direction of motion of
the ship
Boundary layer thickness increases from bow to stern so most of the propeller
(especially on single screw ships) will be within the boundary layer.
Frictional wake is always positive and stronger close to hull (weaker with increased
distance from hull). Strongest of the three components of wake.
Wake strength is influenced by shape of the stern and can not be calculated. Experimental
evidence is needed - “wake survey”