Transcript Multi-tasking - ProSoft - Authorized Mastercam Reseller

Multi-tasking
OKUMA Multus B300W
Multi-tasking
Mori-Seiki NT
Multi-tasking
Mazak Integrex Mark IV
Multi-tasking
Machine Definition
Multi-tasking
Axis combinations
Multi-tasking
Axis combinations
Multi-tasking
Stock Setup
Multi-tasking
Tool Setup – Define lathe tools in B=0 position.
Multi-tasking
Tool Setup – Define lathe tools in B=0 position.
Mazak Integrex
Okuma Multus
Mori Seiki NT
Multi-tasking
Tool Angle – One tool can be defined to work in any possible configuration using
Tool Angle
Tool Angle = BA: Angle
(Okuma Multus)
Tool Orientation on Machine:
Indexes a tool to work on Left
spindle or Right spindle and
for back turning on either
spindle
(M602 or M603- Okuma Multus)
Multi-tasking
Tool Orientation on Machine: Indexes a tool to define Position B
(Okuma Multus - M602 or M603)
N220G97 G95 S=3800 M42 M602 BA=90. TL=011011
Multi-tasking
Tool Orientation on Machine: Indexes a tool to define Position B
(Mori-Seiki NT D1 or D2)
Defining Lathe tool output
Tool ID Code: MR2
For consistency, the general guidelines below are suggested
Multi-tasking
Tool Orientation on Machine: Indexes a tool to define Position B
(Integrex Mark IV - Matrix)
(PROGRAM NAME - MULTI-TASKING DEMO_MJR1 DATE=DD-MM-YY - 22-02-09
TIME=HH:MM - 13:47 )
(POST LICENSE - IN-HOUSE SOLUTIONS INC.)
(T11 | CNMG 08 OD R
| DIA. - 11 | SUFFIX - .02 | INSERT - CNMG 12 04 08)
G21 G69 G80 G40 G18 G90 G94
M205
(UPPER TURRET)
G109 L1
(T11 | CNMG 08 OD R
| DIA. - 11 | SUFFIX - .02 | INSERT - CNMG 12 04 08)
(TOOLPATH GROUP - PREP STOCK )
G21 G10.9 X1
N1 G91 G28 X0.
N1 G28 Y0. Z0.
M901
M202
T11.02 T11 M06
G91 G28 X0. Z0.
G90
M108
G0 G90 G53 B90.
M107
G54
...
Multi-tasking
N220G97 G95 S=3800 M42 M602 BA=90. TL=111111
N230 M4
Multi-tasking
Program: Facing / Drilling / ID Boring
Multi-tasking
Misc Ops: Stock Flip
Multi-tasking
Misc Ops: Stock Flip
Multi-tasking
Face / Drill / ID Bore (rough) / ID Bore undercut finish
Multi-tasking
ID Bore undercut
N220G97 G95 S=2816 M42 M602 BA=-10. TL=330933
N230 M4
Multi-tasking
OD Rough / Finish / Plunge Cut Parameters
Multi-tasking
OD Finish Back turning
N220G97 G95 S=509 M41 M603 BA=90. TL=004004
N230 M3
Multi-tasking
Finish ID / Thread OD
Multi-tasking
Mill slot / Transform toolpath
T/Cplane TOP in Mill is C=90.
BACK is C=0
...
N210G94 SB=2000 M241 M63 M9 BA=90. G52
TL=303030
N220 M13
N230 G138
N240 G17
N250 M146
N260 G0 C90.
N270 M147
N280 G127 B90.
N290 G0 Z155.
N300 X37.5 Y0.
N310 Z65.
...
Multi-tasking
Circle Mill counterbore / Drill / Tap angled holes
Multi-tasking
Misc Ops: Stock Flip back to OP1 position
Geometry exists already. Transfer geometry not required
Multi-tasking
Stock Flip – Original position
Multi-tasking
Face – Stock recognition
Multi-tasking
Rough / Semi-finish ID
Multi-tasking
Rough OD / Finish OD
Multi-tasking
Thread
Multi-tasking
Finish corners