Transcript Overview of 1926 Subpart X

CFR 29 1926 Subpart X
Stairways and Ladders
OSHA Regulations
29 CFR Part 1926
Subpart X - Stairways and Ladders




1926.1050 Scope,
applications, and
definitions, applicable
to this subpart
1926.1051 General
requirements
1926.1052 Stairways
1926.1053 Ladders








1926.1054 Reserved
1926.1055 Reserved
1926.1056 Reserved
1926.1057 Reserved
1926.1058 Reserved
1926.1059 Reserved
1926.1060 Training
1926 Subpart X - App
A - Ladders
Inventive way to use a Ladder
Bottom Line Don’t Try It
1926.1050(a)
Scope and Application

This subpart applies to all stairways and ladders
used in construction, alteration, repair (including
painting and decorating), and demolition
workplaces covered under 29 CFR part 1926,
and also sets forth, in specified circumstances,
when ladders and stairways are required to be
provided. Additional requirements for
ladders used on or with scaffolds are
contained in Subpart L - Scaffolds.
What not to do with Ladders!!
1926.1050(b) Definitions
"Cleat" means a ladder crosspiece of rectangular cross section placed
on edge upon which a person may step while ascending or descending a
ladder.
"Double-cleat ladder" means a ladder similar in construction to a singlecleat ladder, but with a center rail to allow simultaneous two-way traffic for
employees ascending or descending.
1926.1050(b) Definitions
"Extension trestle ladder" means a self-supporting portable ladder,
adjustable in length consisting of a trestle ladder base and a vertically
adjustable extension section, with a suitable means for locking the
ladders together.
1926.1051(a) Provide a stairway or ladder at all personnel
points of access where there is a break in elevation of 19 inches
(48 cm) or more, and no ramp, runway, sloped embankment, or personnel
hoist is provided.
1926.1051a)(2) Provide a double-cleated
ladder or two or more separate ladders when ladders are the
only mean of access or exit from a working area for 25 or more
employees, or when a ladder is to serve simultaneous two-way
traffic.
1926.1052 - Stairways
(a)(1) Stairways must have landings of not less than 30 inches (76 cm) in the
direction of travel and extend at least 22 inches (56 cm) in width at every 12 feet
(3.7 m) or less of vertical rise.
1926.1052 - Stairways
(a)(2) Install stairs between 30
deg. and 50 deg. from horizontal.
(a)(4) Provide a platform where
doors or gates open directly on a
stairway; the swing of the door
must not reduce the effective
width of the platform to less than
20 inches (51 cm).
1926.1052(a)(3) Riser height and tread
depth must be uniform within each flight of stairs, including any
foundation structure used as one or more treads of the stairs.
Variations in riser height or tread depth shall not be over 1/4 inch
(0.6 cm) in any stairway system.
LANDING
Tread
Rise
1926.1052(a)(7) Eliminate slippery conditions
on stairways before the stairways are used to reach
other levels.
1926.1052(c)-Stairrails and handrails
Equip stairways having four
or more risers or rising more
than 30 inches (76 cm),
whichever is less, with:
• At least one handrail; and
• One stairrail system along
each unprotected side or
edge.
1926.1052(c)The height of stairrails
must be as follows:
Stairrails installed after March 15, 1991,
must be not less than 36 inches (91.5 cm)
from the upper surface of the stairrail
system to the surface of the tread, in line
with the face of the riser at the forward
edge of the tread.
Stairrails installed before March 15, 1991,
must be not less than 30 inches (76 cm)
nor more than 34 inches (86 cm) from the
upper surface of the stairrail system to the
surface of the tread, in line with the face
of the riser at the forward edge of the
tread.
1926.1052(c)(5) Handrails and the top rails of stairrail systems must be
capable of withstanding, without failure, a force of at least 200 pounds
applied within 2 inches (5 cm) of the top edge, in any downward or
outward direction, at any point along the top edge.
1926.1052 Stairway Systems
(c)(7) When the top edge of a stairrail system also serves as a handrail
(c)(8) Stairrail systems and handrails surface
(c)(9) Handrails must provide an adequate handhold
(c)(10) The ends of stairrail systems and handrails must not be a projection hazard
(c)(11) Handrails not a permanent part of the structure
(c)(12) Unprotected sides and edges of stairway landings
GOOD OR BAD?
1926.1053 Ladders
1926.1053 Ladders
(a)(2) Ladder rungs, cleats, and
steps must be parallel, level, and
uniformly spaced when the ladder
is in position for use.
(a)(3)(i) Rungs, cleats, and steps
of portable ladders must be
spaced not less than 10 inches
(25 cm) apart, nor more than
14 inches (36 cm) apart, as
measured between center lines of
the rungs, cleats and steps.
1926.1053 Ladders rungs
(a)(4)(ii) The minimum clear distance
between side rails for all portable
ladders is 11 1/2 inches (29
cm).
(a)(5) The rungs of individualrung/step ladders must be shaped
such that employees' feet cannot slide
off the end of the rungs.
(a)(6)(i) The rungs and steps of fixed
metal ladders manufactured after
March 15, 1991, must be corrugated,
knurled, dimpled, coated with skidresistant material, or otherwise
treated to minimize slipping.
1926.1052(a)(12) Coating of Ladders
Wood ladders must not be coated with any opaque covering, except for
identification or warning labels which may be placed on one face only of a side rail.
1926.1053(b) Use
The following requirements apply to the use of all ladders, including
job-made ladders, except as otherwise indicated:
1926.1053(b)(1) When portable
ladders are used for access to an upper
landing surface, the ladder side rails
must extend at least 3 feet (.9 m) above
the upper landing surface
1926.1053(b) Use
(b)(2) Maintain ladders free of oil, grease, and
other slipping hazards.
(b)(3) Do not load beyond the maximum
intended load for which they were built, nor
beyond their manufacturer's rated capacity.
(b)(4) Use only for the purpose for which they
were designed.
(b)(5)(i) Use non-self-supporting ladders at an
angle such that the horizontal distance from
the top support to the foot of the ladder is
approximately one-quarter of the working
length of the ladder (the distance along the
ladder between the foot and the top support).
1926.1053(b) Use
(b)(12) If ladders are used where the employee or the ladder could
contact exposed energized electrical equipment, they must have
nonconductive siderails, except as provided in 1926.951(c)(1) of this
part.
Aluminum
Wood
1926.1053(b) Use
(b)(13) Do not use the top or
top step of a stepladder as a
step.
(b)(14) Do not use crossbracing on the rear section of
stepladders for climbing unless
the ladders are designed and
provided with steps for
climbing on both front and rear
sections.
1926.1053(b) Use
(b)(15) Must be inspected by a
competent person for visible defects,
e.g., broken or missing rungs, cleats,
or steps, broken or split rails, corroded
components, or other faulty or
defective components.
(b)(17) Withdraw from service until
repaired: fixed ladders with structural
defects, e.g., broken or missing rungs,
cleats, or steps, broken or split rails, or
corroded components.
(b)(17)(i) Tag immediately with "Do
Not Use" or similar language.
(b)(17)(ii) Mark in a manner that
readily identifies it as defective.
Remove from service
1926.1053(b) Use
(b)(20) Face the ladder when
ascending or descending.
(b)(21) Use at least one hand to
grasp the ladder when
progressing up and/or down the
ladder.
(b)(22) Do not carry any object or
load that could cause you to lose
balance and fall.
Missing rung
• Improper angle
• No extension
Ladders and Stairway Citations
Standard
#Cited
#Insp.
Penalty
CFR 29 1926.1051
CFR 29 1926.1052
CFR 29 1926.1053
CFR 29 1926.1060
76
428
498
58
72
305
372
57
$ 32,259
$ 187,234
$ 234,475
$ 10,134
Information Gathered from www.osha.gov Inspections
Conducted October 2002 through September 2003.
1926.1060 Training
(a) Must train each employee using ladders and stairways, as necessary, to
recognize hazards related to ladders and stairways, and the procedures to be
followed to minimize these hazards.
(a)(1) A competent person must train each employee in the following areas, as
applicable:
(a)(1)(i) The nature of fall hazards in the work area;
(a)(1)(ii) The correct procedures for erecting, maintaining, and disassembling the fall
protection systems to be used;
(a)(1)(iii) The proper construction, use, placement, and care in handling of all stairways
and ladders;
(a)(1)(iv) The maximum intended load-carrying capacities of ladders and
(a)(1)(v) The standards contained in this subpart.
(b) Retrain each employee as necessary to maintain the understanding and knowledge
acquired through compliance with this section.
More Inventive ways to use a Ladders
Bottom Line Don’t Try It
More Inventive ways to use a Ladders
Bottom Line Don’t Try It
More Inventive ways to use a Ladders
Bottom Line Don’t Try It
More Inventive ways to use a Ladders
Bottom Line Don’t Try It
More Inventive ways to use a Ladders
Bottom Line Don’t Try It
Thank You
DISCLAIMER
This information has been developed by an
OSHA Compliance Assistance Specialist and is
intended to assist employers, workers, and
others as they strive to improve workplace
health and safety. While we attempt to
thoroughly address recordkeeping, it is not
possible to include discussion of everything
necessary to ensure a healthy and safe
working environment in a presentation of this
nature. Thus, this information must be
understood as a tool for addressing
workplace hazards, rather than an exhaustive
statement of an employer’s legal obligations,
which are defined by statute,
DISCLAIMER
regulations, and standards. Likewise, to the
extent that this information references
practices or procedures that may enhance
health or safety, but which are not required by
a statute, regulation, or standard, it cannot,
and does not, create additional legal
obligations. Finally, over time, OSHA may
modify rules and interpretations in light of new
technology, information, or circumstances; to
keep apprised of such developments, or to
review information on a wide range of
occupational safety and health topics, you can
visit OSHA’s website at www.osha.gov