Transcript Document
ILFS New Technology and Product Presentation Presented By: Scott Goldstein-President HIGHLY CONFIDENTIAL 0 Fugitive Adhesive and Dry Peel Requirements: • Hot Melt • Clean release • Water-base • Tackless or retack (if desired) Recommendations: • 57-482 to 57-486 Series • All fugitives must be tested on specific stock. • Water-base Repositionable to be diluted with water. • 57-5071 (Lowest release value at 11 grams) • 57-5074 (Higher release value at 20 grams for offset stocks and envelope flap) • 41-24-1 • Hot Melt. Great anti-stain. Clean release. 1 Dry Peel • Water-base with UV Topcoat (26-35-1 with L9091VT) • Hot Melt with UV Topcoat (28-67-5 with L9042M) Refer to www.inlinefinishingsolutions.com for process schematic. 2 UV Silicone Release Coating/Repositionable and Permanent Hot Melt and Water-base Adhesives For Hand Applied Labels: • Apply L9091L free radical UV silicone via pattern gluer with photopolymeric plate, and then apply 37-625 repositionable, or ANY standard permanent pressure sensitive hot melt. • Apply L9091L free radical UV silicone via pattern gluer with photopolymeric plate, and then apply 30-37-3 semi-permanent water-base pressure sensitive. • Note: 300 fpm/400 watt lamp For Premium Release/Auto Dispensed Labels: • PC-605 cationic UV silicones applied via flexo with photopolymeric plate with permanent PSHM 16-66-2 or repositionable PSHM 37-625. • Refer to www.inlinefinishingsolutions.com for process schematic. 3 Water-base Release Coating/Repositionable or Permanent Hot Melt Machine Requirements: • Apply L9100 M (2 component system) via flexo applicator with photopolymeric plate. L9100 M exhibits clean release with both permanent and repositionable hot melt pressure sensitives, and with semi-permanent water-base PSA (30-37-3). Dry with standard convection air at 220-250ºF for 0.5 sec dwell. 4 Benefit Summary of ILFS’s Integrated Label Technology Far More Cost Effective • Offers a 33% cost savings over purchasing pre-converted release liner/pressure sensitive face stock and tipping it on to the web. • Offers a 41% cost savings over purchasing and tipping on coated release liner alone. • Offers further savings due to your ability to pattern-apply release coating and adhesive only in the areas that it is required. Faster Production • Eliminates the need for slow, tip-on label application of pressure sensitive labels to the web allowing you to increase web speeds up to 800+ fpm. 5 Benefit Summary of ILFS’s Integrated Label Technology Reduced Inventory Carrying Costs • Eliminates the need for large inventories of converted pressure sensitive roll stock and allows you to convert on a just-in-time production basis. Additional Printing Surface • You can print or image directly under the release coating to convey additional messages to customers after they have removed the label. Elimination of Stacking Problems • Because two panels unite to form one continuous surface, the 4 mil imbalance created by tipping on release liner and pressure sensitive stock is eliminated. The result is a smooth, integrated label product that stacks flat on skids. 6 Current New Business Development Opportunities • Textured and High Profile (MBOSS) UV Topcoat (L9074V) for Screen over AGS films. L9074V for Screen over Low to 0% wax/silicone containing heat set varnishes. L9082T for flexo for over varnish application and over AGS films. L9066H for chemical texturing. • UV Glitter and Pearlized Topcoat (press side add 26-35-3) • UV and Water-base Glow-in-the-dark Coatings (For Screen and Flexo: UVS100V (green) and UVS102V (blue). Coat weights at 0.5-1 mil. • UV Thermochromic (UVS101V [flexo] and UVS109V [Screen]). 31ºC activation temp. Flexo applied at 1-1.5 mil coat weight. Black to clear. • UV Silver/Gold Scratch-off (L9093HS or HG). Run over 96U152H/L9091L (90:10% to 80:20%) primer. Use Gallium doped, V-Bulbs if enhanced cure is needed. • Hot Melt Remoistenable (28-57-4). 7 Current New Business Development Opportunities • Magnetized UV Varnishes for Low-end Magnet Promotions (UVS107V Binder/A6256P Powder w/A6428P Primer). • UV Laminating Adhesive (UVA 105 M for Standard Performance). • UV Pressure Sensitive Adhesive (UVPS100E). • • For cold foil applications For “plastic card” laminations • Magnetic UV Varnish for Information Strips on Credit Card (For E-beam only) • UV MBoss replacement for traditional raised image foil stamping (L9213S). 8 In-Line Magnets Manufacturing • Lay down high-profile magnetic UV at 3.5-4.5 mil via rotary screen coater (80/40 mesh). • Cure UV with Gallium doped V-bulb. • Magnetize UV with Multi-pole magnet roller. • Charged piece can either be sheeted or finished in-line like kiss die cut labels. 9 In-Line Magnets 10 • Allows magnets to be produced on paper (vs. vinyl). • Allows for personalization. • Allows for pattern application, reducing cost and waste. • Allows for pattern coating with a 1/16 inch border, SIGNIFICANTLY increasing life of dies • Postal savings due to 67% lower weight of piece.