Transcript isotopes-workshop-srf---mcintosh-v2

SUPERCONDUCTING RF (SRF) SYSTEMS
Peter McIntosh (STFC)
Accelerator-driven Production of Medical Isotopes
8th – 9th December 2011
1
Outline
•
•
•
•
•
•
2
Medical Isotope Generation
The Photo-Fission Process
Accelerators and Isotope Production
Superconducting RF Technology
SRF Accelerator Solutions for 99Mo Production
Conclusions
Medical Isotopes
• Radioisotopes have become a
vital tool for scientific research
and industry:
– applications in medicine,
biology, physics, chemistry,
agriculture, national security
and environmental and
materials science.
• The ability to attach
radionuclide to a
pharmaceutical agent for
transport to the desired site is
key to its effectiveness for
medical applications.
3
• Positron Emission Tomography
(PET) scans, produce detailed
maps of active areas in the
brain and other organs.
Technetium-99m has become
the workhorse of diagnostic
nuclear medicine:
– with over 50,000 procedures
performed each day in the U.S.
99mTc
Production
• The half-life of an isotope must be long enough to
allow transport from production sites to end-use
locations without excessive loss, and short enough to
minimize the unwanted radiation dose to the patient
after the procedure is complete.
• The use of “generators,” involves a longer-lived parent
(2.75-day 99Mo) that decays to a shorter-lived daughter
(6-hour 99mTc).
• Specialized reactors produce
the 99Mo as a fission fragment
for transport to end-use sites,
where clinicians “milk” the
99mTc daughter from the
generator as needed.
4
99Mo
Production
(a) Neutron fission of 235U
(present-day reactor technique).
(b) Neutron-capture process
on 98Mo.
(c) Photo-neutron process on
100Mo.
(d) Photo-fission of 238U.
5
Photo-Fission Process
E-Linac
Electron
Photon
Converter
238U
Target
Ion
Source
Mass
Separator
Neutron
High energy
photon
6
Users
Fission
fragments
Neutron
Neutron
Photo-fission of 238U was proposed by W. T. Diamond
(Chalk River) in 1999 as an alternative production method
for RIB.
RIB
Fission
fragments
HEU Reactors and Accelerators
• Specific isotopes from
accelerator induced nuclear
reactions, using appropriate
beam species and energies:
– Typically 10 – 100s MeV protons
• Major advances in high-power
particle accelerators and highpower target technologies offer
significant advantages for isotope
production via spallation-induced
neutron irradiation.
• Isotope sources are produced
using either reactors or
accelerators of varying sizes.
• 99Mo is a fission fragment that
is today typically produced
using Highly Enriched Uranium
(HEU) reactors.
7
SRF Accelerators
• Superconducting RF (SRF) accelerator technology is
capable of 20x beam power required, which using
rapid-switching techniques could distribute beam
simultaneously to many target stations.
• Electron beam accelerator technologies show promise
for radionuclide production, either via photo-nuclear
reactions with MW-class beams, or using Compton
backscatter of high-intensity laser beams with highquality light source beams.
• A high-power accelerator facility could provide a
reliable source of neutron produced isotopes such as
99Mo, and also have sufficient power and flexibility to
supply a steady stream of research isotopes.
8
Superconductivity Benefits
• Both Normal-conducting RF (NRF) and SRF accelerating structures
can produce high gradients (10s of MeV/m), but only SRF
technology can sustain high duty operation.
• The power dissipated for CW operation in a NRF structure is
potentially enormous, but not so for SRF cavities.
• RF power required to generate an accelerating voltage (Vacc) is
defined by:
2
Pc 
V acc
2R
Q
Qo
• The ratio of shunt resistance to quality factor (R/Q), which depends
on cavity geometry, is not vastly different between NRF and SRF
cases; and so the cavity power (Pc) required is dominated by the
bare quality factor Q₀, which is typically 105 times larger for SRF.
• Overall, SRF reduces the wall plug power compared to NRF, by a
factor ~200, reducing power consumption from MWs to kWs.
9
Neutron Amplifier Target for Isotope Production in
a SRF Based Accelerator Facility at ANL
• The SRF linac uses energy recovery linac (ERL) technology, whereby
the electron beam is transmitted through the target and is
recollected and re-injected into the accelerating structure.
• The recollected beam transfers beam power to the injected
electron beam, and reduces the amount of RF power required to
accelerate the electrons to their final energy.
• ~10 x less RF power compared to non-ERL linac technology.
• The SRF linac is only ~ 2 meters long making it compact in
comparison to existing NC technology. The energy recovery
efficiency is >95%. The depleted beam power is dumped into a low
energy beam stop, which is physically separate from the target.
Courtesy J Nolan, ANL
10
Accelerator Flexibility
• The beam energy, target thickness, and recovered power can be
optimized for maximum isotope yield.
• The target has a vacuum loadlock, which can be removed from the
target chamber and a new target installed without breaking vacuum
or stopping the linac operation.
• The activated target requires robotic control, but this is a well
established technology.
• System has a number of advantages over conventional linac
technology:
–
–
–
–
–
more compact,
higher current for increased yields,
improved thermal management of waste beam power,
a continuous target feed,
and multiple target capability.
• The linac can also be configured for other isotope production, e.g.
67Cu, which requires similar energies to 99Mo.
11
ARIEL E-Linac at TRIUMF
• Advanced Rare IsotopE
Laboratory as part of the
ISAC facility at TRIUMF.
• New complementary
electron linac (E-linac)
driver for photo-fission.
• New proton beamline.
• New target stations and
front end.
• Staged installation
proposed.
12
ARIEL E-Linac Parameters
Parameter
Value
Bunch Charge
16 pC
Bunch Repetition Rate
0.650 GHz
Frequency
1.3 GHz
Average Current
10 mA
Energy
50 MeV
Beam Power
0.5 MW
Duty Factor
100 %
Bunch Properties
Injected
Ejected
Normalised Emittance (µm)
-30
-100
Longitudinal Emittance (eV.ns)
-20
-30
Bunch Length (FW), inject (ps)
-170
-30
<1 keV
<1 %
Energy Spread (FW)
13
}
}
The requirement:
50 MeV × 10 mA
= 0.5 MW beam
power
Not critical; beam
dumped on target
ARIEL E-Linac Layout
Gun 100 keV, 650 MHz
Buncher
Injector
10 MV/m, Q=1010
10 mA, 5-10 MeV gain
≤100 kW beam power
Main Linac
Two cryomodules
Two cavities/module,
10 MV/m, Q=1010
10 mA, 40 MeV gain
≤400 kW beam power
Solenoids
Capture Cavities
Solenoid
9-cell Cavities
• Division into injector & main linacs allows:
– Possible expansion for:
• Energy Recovery Linac (ERL) – e.g. 10 mA, 80 MeV
• Recirculating Linear Accelerator (RLA) – e.g. 2 mA, 160 MeV
14
MW Class SRF Linac
The present E-linac design concept, based on 1.3 GHz Superconducting RF
technology (SRF) in CW operation, offers flexibility, possibility for expansion
to other applications (Free Electron Laser, Energy Recovery Linac).
15
Staged Implementation
16
E-Linac High Power RF Delivery
17
ARIEL Injector Cryomodule
Cryo-insert with 4K phase separator.
2K JT valve & HX not shown.
Insulating
vacuum
77K thermal
shield
Input
coupler
Strong back
Cavity
string
18
Warm/cold
transition
Main Linac Cryomodule
Cold Mass
Scissor Tuner
Input Couplers
19
Integrated
Cryomodule
HOM Mitigation
• RF generator drives
fundamental mode, E-beam
drives all modes, leaves
wakefield, leading to beam
break up (BBU) instability.
Analysis defines the criteria
of (Rd/Q)⋅QL < 107 ohm.
• Modelling 9-cell cavity
found TE111 trapped dipole
mode at 2.56 GHz with Rd =
3e7Ω.
• Asymmetric end cells &
beam pipes push the mode
towards the tuner end.
20
• Use SS rings or other damping
material to damp dipole to
1e7 Ω.
• Back-up solution – use HOM
couplers.
E-Linac Implementation
ERL
Upgrade
HPRF
RLA
Upgrade
SRF
Cryomodules
21
Cryoplant
Gun & LEBT
Conclusions
• High power accelerators are a viable alternative to
conventional HEU reactors.
• SRF linac technology provides significant power
advantages compared to conventional linac technology:
– Order of magnitude higher if ERL techniques are employed
– Significant capital and operational cost savings
• SRF accelerators also provide wide flexibility in terms of
beam power, allowing optimisation for a variety of
isotope species and effective yield.
• SRF linac solutions for 99Mo production are now
becoming a reality using proven accelerator
technology.
• Funding agency priority is now being demonstrated!
22