Transcript ICRA Panel System Installation Instructions

ICRA Panel Installation Steps
ICRA Panel System
Installation Instructions
ICRA Panel Installation Steps
Determine Starting Point
1. Layout corners, angles,
obstacles so that the
panel sizes will fit
together nicely and not
create a gap at any point
of the installation.
NOTE: If the first panel comes off the
wall, place the track at 24” from the wall.
ICRA Panel Installation Steps
Install 3” Blue Tape to protect the Facility
2 & 3. Establish the starting
point on one of the walls.
Run 3” Blue Tape from ceiling
to floor as the center point of
the ICRA wall.
ICRA Panel Installation Steps
4. Install the Ceiling Frame
Clip track to center beam of ceiling grid.
Double sided foam tape to ceiling
grid or Hard Lid.
ICRA Panel Installation Steps
5. Determine the location of the Floor Angle Metal Strip.
Drop the “String Line” from the Ceiling Track as a level to
establish the placement of the Floor Angle Metal Strip.
ICRA Panel Installation Steps
7. Starting next to the wall, insert the first
ICRA Panel by sliding it into the Ceiling
Track & placing it against the Floor Angle
then sliding it over to meet the wall.
ICRA Panel Installation Steps
Installation Tips:
Place a 12” strip of White tape on the metal strip on the back of the panel slider.
Once the panel is set to the desired height, press the tape onto the coroplast. It
will stick and hold the panel slider in place.
Manometer: Hold back tape, then release when meter is level.
ICRA Panel Installation Steps
Assembly of Additional Slider to reach 13’ wall height
Insert 2nd slider on
the bottom of the
panel.
Remember that the top slider will be the final fit:
Measure and identify desired placement of the
bottom slider.
ICRA Panel Installation Steps
Assembly of Additional Slider to reach 13’ wall height
Place ONE screw on back side on each side
of slide to maintain desired position.
ICRA Panel Installation Steps
Assembly of Additional Slider to reach 13’ wall height
Re-assemble the top slide if it was
removed earlier.
The Preferred method of securing the
top slide is with tape on the back
supporting rail. (Ref. Slide #7)
ICRA Panel Installation Steps
Sealing the Seams
12. Once a large section of the wall is installed, run 3” White tape along
the top and bottom of the panel wall sealing it to the Blue tape on the
ceiling and floor to make a complete air tight seal.
ICRA Panel Installation Steps
Door Installation
• ** For best results: Mount the door in between 2 ICRA
Panels for stability and strength.
•
NOTE: The Door and Frame are held square by 3 screws and 1/8” spacers placed
through the wood frame into the door. KEEP THESE SCREWS INTACT during the
installation to insure square-ness of the installation.
ICRA Panel Installation Steps
Door Installation
NOTE:
There is a 1” frame on the door panel . Add 1” from the last ICRA Panel
installed before making the cut on the Floor Angle.
•
1
1
.
Measure the exterior dimension of the
WOODEN Door Frame (37-1/4”)
ICRA Panel Installation Steps
Door Installation
16. Insert the door in the same fashion as an ICRA Panel.
20. Measure, cut and install the coroplast on the top of the
door.
ICRA Panel Installation Steps
21. Remove the 3 screws and 1/8” spacers from
the door and frame.
ICRA Panel Installation Steps
Door Installation
23. Double check for proper function and level.
24. Run 3” Tape over the threshold of the door
covering all of the exposed metal.
ICRA Panel Installation Steps
25. Resume installing the next ICRA Panel.
ICRA Panel Installation Steps
Disinfecting the ICRA Wall
26. Wipe the entire wall down with a
Disinfectant Spray or wipe.
ICRA Panel Installation Steps
PROPER Panel
System Storage
ICRA Panel Installation Steps
IMPROPER Panel Storage
ICRA Panel Installation Steps