Transcript COMIND

EXTENSION CABLES FOR
RADIO / GPS / PHONE
DESIGN AND PRODUCTION OF EXTENSIONS
CABLES FOR SIGNAL TRANSPORT.
ON THE BASIS OF STUDIES ON FREQUENCY AND WORK
ENVIRONMENT AND THE TYPE OF CONNECTIONS, ARE
USED THE MOST SUITABLE PARTS THAT THE MARKET
CAN OFFER:
•
•
•
•
•
•
•
•
RG174 cable @50 Ohm
RG58 cable @50 Ohm
75 Ohm cable
Cable Shield >= 98%
GT5 connectors
FAKRA connectors
MCX & MMCX connectors
RAKU/RAST connectors
RADIO ANTENNA ADAPTERS
CABLE AND CONNECTIONS ON CUSTOMER REQUEST
Double radio antenna
adapter cable, input HIROSE
output ISO 10599
Radio antenna adapter cable,
from RAKU II to male ISO
10599
Radio antenna adapter
cable, from HIROSE to ISO
10599
RADIO ANTENNA ADAPTERS
CABLE AND CONNECTIONS ON CUSTOMER REQUEST
Radio antenna adapter cable
from female ISO 10599 to male
STD EU
Radio antenna adapter cable
to ISO 10599 with power
Radio antenna adapter cable
from female STD EU to male ISO
10599
AERIAL CABLES FOR KEYLESS OPENING
We produce Aerial cables
for remote opening
(keyless).
The aerial is made of
50Ohm nominal
impedance cable.
The frequency range of
the antenna is obtained
by varying the length of
the cable and the length
of the hot lead.
PROBE CABLES FOR
ABS & TCS CONTROL UNIT
Production of probe
cables for ABS & TCS
control units.
Realized on customer
specifications, this
product must pass very
selective electrical
tests before to be
marketed.
PROBE CABLES FOR
ABS & TCS CONTROL UNIT
The connector is realized by
injection molding directly on
cable and terminals, for a
tight seal on top of
commercially available
connectors.
The electrical test includes a
test for continuity and
polarity, and an insulation
test between conductors
and connector >=10Mohm
and an additional dielectric
strength test using a
discharge >= 1000Volts.
PRODUCTION OF COMPLEX HARNESSES
FOR THE MEDICAL INDUSTRY
Cabling of equipment for
the medical industry.
Connections for data
transfer (Serial, Ethernet,
USB, etc.).
Electrical test of
harnesses with insulation
tests >20Mohm to
ensure the reliability of
tests and preserve the
safety of the patient and
of the user.
COMPLEX HARNESSES PRODUCTION
FOR ALL INDUSTRIES
•
•
•
•
•
•
•
•
AUTOMOTIVE
MOTORBIKES
MARINE INDUSTRY
ROAD TRANSPORT
RAILWAY TRANSPORT
EARTH MOVING
MEDICAL EQUIPMENT
MAJOR & SMALL APPLIANCES
ENGINE COMPARTMENT HARNESSES
FOR AUTOMOTIVE AND MARINE
INDUSTRY
• Electronic injection
• Power cables
• Shielded cables
• Alternator cables
• Group climate
• Engine wiring
ECU FOR ENGINES
ELECTRONIC COMPONENTS
CARDS FOR DATA ACQUISITION
AND ACTUATORS CONTROL
PRINTED CIRCUIT BOARDS FOR
ELECTRONIC EQUIPMENT
MANAGEMENT
PLASTIC OVERMOULDING ON CABLES
AND CONNECTIONS
HOTMELT and INJECTION MOULDING TECHNOLOGY
Thanks to the internal construction of the molds, we can follow the project through
all its stages and speed up the development of the product.
PLASTIC OVERMOULDING ON CABLES
AND CONNECTIONS
HOTMELT and INJECTION MOULDING TECHNOLOGY
MAIN PRODUCTION EQUIPMENT
KOMAX CUT STRIP CRIMP
MACHINES MOD. GAMMA333PC,
ALPHA433.
IN LINE INKJET PRINTER
IMAJE S8 MASTER
MAIN PRODUCTION EQUIPMENT
PLASTIC INJECTION MOLDING
MACHINES EXMA PLUGMATIC ST4
ULTRASONIC WELDING MACHINE
SCHUNK RK2000
MECHANICAL DIVISION
MICRO TURNING:
The micro turning is capable to produce mechanic
smallwares of high precision.
The processable materials are brass, steel,
stainless steel, mild steel, copper, nickel,
aluminum, titanium and plastics.
The characteristic of the micro turning is the
precision processing of small parts.
Our machinery fleet is able to produce turned
parts from a minimum diameter of 0.50 mm to a
maximum diameter of 22.00 mm.
Examples of feasible products: bushings, bolts,
threaded inserts, precision extractors, copper
inserts, electrical contacts, etc.
MECHANICAL DIVISION
METALLIC CARPENTRY:
Construction of:
Metal containers for automotive components
Specific containers for companies that produce bulky plastic
material
We produce to customer specifications and / or with the help
of our technical dept.
Design / project service
Prototype production
Mass-production
Existing products modification
Epoxy powder coating
Plastic coating of metal
Any special treatment, on request
TECHNOLOGY
&
DEVELOPMENT
All productions arise from a continue
technical collaboration with the customer
through the methodology APQP (Advanced
Product Quality Planning).
Already from project phase, functionality and
reliability of the product is best ensured
applying the technique Failure Mode Effects
Analisys (FMEA).
The technical drawings of products are made
by the Technical Department, with
indications by the customer, as the first
prototypes from the prototypes laboratory.
The qualification of the product is made
using the PPAP standard (Production Part
Approval Process).
Also Comind make technical assistance in all
plants of its customers, making use of a
circuit of international companies already
present in the area, with proven expertise
and capacity.
QUALITY
Customers satisfaction is one of the first
objectives of the Company.
Our quality management system, compliant and
certified ISO/TS16949: 2009 is a guarantee for
our customers, who experience our desire to
satisfy not only in terms of product quality, but
for every service rendered to them.
The annual monitoring of the certification
agency and our continuous internal audits,
ensures the application of the rule.
In fact, the Comind meets the requirements
established by the International Automotive Task
Force, the international agency that regroup the
world's largest manufacturers of motor vehicles.
Alife plant
Comind S.r.l. – web: www.comind-srl.it – mail: [email protected] – phone: +39(0)823788867 fax: +39(0)823787382
Registered office: Via Sannitica 50 81016 Piedimonte Matese CE – Productive plant: SP 249 Torrione Puglianello 81011 Alife CE