幻灯片 1 - Huawei
Download
Report
Transcript 幻灯片 1 - Huawei
Security Level: 秘密
Huawei WLAN Stadium
Coverage Solution
www.huawei.com
HUAWEI TECHNOLOGIES Co., Ltd.
HUAWEI Confidential
Contents
1
Project Preparation
2
Product Selection
3
Bandwidth Design
4
Deployment Design
5
Project Case
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 2
WLAN Planning Steps
Project
Requirement
collection
Pre-sales
network
planning
Customer
communication
and quotation
Detailed site
survey
After-sales
network
planning
Delivery
Product selection
Bandwidth design
AP capacity design
Network
planning
solution
AP deployment
Channel planning
Cable route and power supply design
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 3
Requirement Collection and Site Survey
Item
Description
Prepare a scale drawing of the stadium and learn the stadium structure (some pictures or materials can be found on the
Stadium structure
Internet).
Coverage area
Determine the target coverage areas, including the stand, parking lot, and corridor.
Obtain user distribution information, including the total number of users in the stadium, user distribution on each stand.
User distribution
Usually, the user density varies in different areas of the stadium.
Service type
Describe the major types of services transmitted on the WLAN: video, web page browsing, or VIP.
Percentage of
Check whether the customer has special requirements on the percentage of concurrent users. Usually, the number of
concurrent users concurrent users accounts for 20% of total users.
Usually, the ratio of 2.4 GHz terminals to 5 GHz terminals is 1:1. The proportion of 5 GHz terminals increases as more and
Terminal type
more 5 GHz devices are used.
Available
Check available 5 GHz channels supported at the local site.
channels
Safety
Check whether CE or FCC compliance is required.
certification
Installation
Learn the preferred installation positions of customers and determine the possible installation positions with the customer.
position
Operating
Check whether the local temperature and humidity meets requirements.
environment
To ensure successful delivery of the network planning solution, conduct detailed site surveys at the
early stage to collect related information and clarify customer requirements according to Stadium Site
Survey Information List. ☞
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 4
Contents
1
Project Preparation
2
Product Selection
3
Bandwidth Design
4
Deployment Design
5
Project Case
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 5
AP Selection: Indoor Settled APs
AP5010 series
AP5010SN/DN
AP6010 series
AP6010SN/DN
AP7110 series
AP7110SN/DN
Product positioning
Small and medium enterprises,
mid-range market
Small, medium, and large enterprises,
mid-range market
Medium and large enterprises
MIMO
2x2
2x2
3x3
Number of concurrent
users supported
30/50
40/60
60/100
Maximum number of
users supported
128
128
128
Antenna type
Built-in antenna
Built-in antenna
External antenna
Maximum transmit
power for each antenna
17 dBm*
20 dBm*
20 dBm*
Power consumption
6.0 W / 9.5 W
6.5 W / 10.2 W
8.7 W / 15.7 W
Power supply mode
PoE: -48 V DC
PoE: -48 V DC
PoE: -48 V DC
BYOD
Y
Y
Y
High-density mode
-
Y
Y
Working mode
Fit/Fat
Fit/Fat
Fit
Operating temperature
-10-50℃
-10-50℃
-10-55℃
Wi-Fi standard
a/b/g/n
a/b/g/n
a/b/g/n
Huawei APs
Appearance
"*"- Transmit power of the antenna can be adjusted according to
requirements of different countries.
Select proper indoor AP models to cover indoor corridors, VIP rooms, and lounges based on user density, area structure, and wall distributions.
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 6
AP Selection: Outdoor APs
Outdoor series
AP6510DN
Outdoor series
AP6610DN
High-density mode
Y
Y
MIMO
2x2
2x2
Number of concurrent users supported
60
60
Maximum number of users supported
128 per radio
128 per radio
Antenna type
External antenna
External antenna
Maximum transmit power for each
antenna
26 (2.4 GHz)+20 (5 GHz) dBm*
27 (2.4 GHz) + 24 (5 GHz) dBm*
Power consumption
25.5 W
30 W
Power supply mode
PoE: -48 V DC
Local AC power supply
Working mode
Fit/Fat
Fit/Fat
Operating temperature
-40-60℃
-40-60℃
Wi-Fi standard
a/b/g/n
a/b/g/n
Uplink interface
ETH: 10/100/1000M
SFP or ETH
Protection grade
IP67
IP67
Huawei APs
Appearance
"*"- Transmit power of the antenna can be adjusted according to
requirements of different countries.
1. Usually, stands of a large stadium are semi-open. Rains, dews, and direct sunlight may cause damage to APs; therefore, outdoor APs
are recommended.
2. At the stands, if the distance between the AP and access switch is smaller than 80 m, use the AP6510DN (PoE power supply is
supported).
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 7
Antenna Selection
18° (2.4 GHz)
15° (5 GHz)
60° (2.4 GHz)
60° (5 GHz)
Number of antennas
required by each AP
1
1
1
1
Applicable frequency
2.4 GHz
5 GHz
2.4 GHz
5 GHz
Gain (dBi)
18 *
19 *
11.5 *
12 *
Horizontal lobe
18°
15°
60°
60°
Vertical lobe
18°
15°
30°
30°
Polarization mode
Dual-polarized
Dual-polarized
Dual-polarized
Dual-polarized
Interface
N-female*2
N-female*2
N-female*2
N-female*2
Applicable APs
AP6510DN
AP6610DN
AP6510DN
AP6610DN
AP6510DN
AP6610DN
AP6510DN
AP6610DN
Dimension (mm)
340*340*25
250*250*25
250*155*60
230*145*55
Part number
27011344
27010890
27010812
27010889
Appearance
"*" -Attenuators need to be configured to meet safety
certification requirements of different countries.
1. It is recommended that you use small angle antennas in areas with a high user density, such as the stands. Small angle
antennas can control the AP coverage area within the effective range to reduce interference.
2. Use 60°antennas in areas with a low user density, such as the parking lot.
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 8
Contents
1
Project Preparation
2
Product Selection
4
Bandwidth Design
5
Deployment Design
6
Project Case
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 9
Terminal Bandwidth Design
Key indicator: delay < 4s
Typical applications and their percentages on the
live network
Key indicator of web page browsing: delay
Key Indicator & Typical Value
Medium
Data
Application
HTML page
browsing
Symmetry
One-way
delay
One-way
Impact
< 4s/Page
N/A
Packet loss
N/A
Source: 3GPP 22105
Ensure good user experience: delay < 4s
Application
10, 2012 CQ of some Operator
Source: 10, 2012 CQ of some Operator
Key Factor that Affects
Service
Experience
Display delay: < 3s
Quite smooth
Excellent
Display delay: 3-8s
Smooth
Good
Display delay: 8-15s
Congested
Poor
Experience
HTML page
browsing
Source: Huawei mLab
Most applications on the current network require a delay smaller than 4s.
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 10
Terminal Bandwidth Design
Bandwidth requirements for stadium mainstream applications
Web page browsing is used as an example. The required bandwidth is calculated as follows:
Rate = size of a web page/delay = (200 KB x 8)/4 = 400 kbps
Bandwidth required by typical applications
Applications
Required Data Rate
Remarks
Web page
browsing
160-400 kbps
Size of a web page: 200 KB; delay: 4 to 10s
Video streaming 280-560 kbps
Real-time services
Instant
messaging
32-64 kbps
2 KB/Session, 0.5s
Email
400 kbps
100 KB/Session, 2s
Social
networking
200 kbps
50 KB/Session, 2s
VoIP
256 kbps
Real-time services, for example, 256 kbps GBR for Face Time
Game
200 kbps
25 KB, 1s
Video services require a bandwidth of 500 kbps, and other applications require a bandwidth of 250 kbps.
Example:
A stadium plans to construct a WLAN for web page browsing, photo uploading on social networks, and video playing. The
average bandwidth required by terminals is calculated as follows:
40% x web page browsing + 40% x social networking + 20% x video playing = 400 kbps x 40% + 200 kbps x 40% + 500 kbps x
20% = 340 kbps
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 11
Concurrent User Model
Fans within the
coverage area of
the APs
Fans connected to
the Wi-Fi network
Fans that use the
network
concurrently
Example:
Seating Capacity
Quantity Percentage
Audience members with smart phones
Smart phones connected to the Wi-Fi
network
Smart phones that use Wi-Fi services
concurrently
80000
100%
80000
100%
24000
30%
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
30% smart terminals use WLAN services
concurrently.
Page 12
Contents
1
Project Preparation
2
Product Selection
3
Bandwidth Design
4
Deployment Design
5
Project Case
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 13
Typical Coverage Mode (1)——Side Mode
AP distance > 7.5 m (four 2.4 GHz channels are used)
Last row of seats
Stand
First row of seats
1.
2.
Use 18° 2.4 GHz antennas and 15° 5 GHz antennas.
Ensure that AP distance is larger than 7.5 m to prevent interference
among APs.
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Football ground
Page 14
AP6510DN or AP6610DN
Typical Coverage Mode (1)——Side Mode
Ceiling
Stand
Football ground
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 15
Typical Coverage Mode (1)——Side Mode
1.
2.
In side mode, APs and antennas can be installed above the seats in the last row of each layer. APs are
placed in a line, which facilitates cable deployment and power supply (See Figure 1).
If APs are installed at places near the audience, hide the APs, for example, hiding APs behind the billboards,
as shown in Figure 2.
Figure1
Figure 2
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 16
Typical Coverage Mode (2) ——Overhead Mode
AP distance > 7.5 m (four 2.4 GHz channels are used)
Last row of seats
Second layer
First row of seats
Last row of seats
First layer
First row of seats
Football ground
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
AP6510DN or AP6610DN
Page 17
Typical Coverage Mode (2) ——Overhead Mode
Ceiling
Stand
Football ground
AP6510DN or AP6610DN
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 18
Typical Coverage Mode (2) ——Overhead Mode
1.Deploy APs in overhead mode if no proper
installation position is available or customers do not
approve installations in the last row of seats.
2.Use 18° 2.4 GHz antennas and 15° 5 GHz
antennas.
3.Properly design channels of APs to prevent that cochannel interference degrades AP performance.
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 19
Typical Coverage Mode (3) ——Floor Mode
Ceiling
Stand
Football ground
AP6510DN or AP6610DN
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 20
Typical Coverage Mode (3) ——Floor Mode
1. Deploy APs in floor mode to enhance signal
coverage if the stand depth is larger than 25 m or
the user density is high (some stadium may have
no standing areas).
2. Adjust downtilt angles of antennas installed above
the last row of seats or on the ceiling to control
coverage areas.
3. Properly design channels of APs to prevent that
co-channel interference degrades AP performance.
4. Signals need to pass through concrete panels,
seats, and people, which makes them attenuate.
Carry out tests to verify the signal attenuation.
Use indoor APs if the signal attenuation is small,
and use outdoor APs and antennas if the signal
attenuation is large.
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 21
Coverage Mode Comparisons
Coverage Mode
Advantage
Disadvantage
Recommends
Side
1. APs and terminals are visible to each
other in line-of-sight distance, with
penetration loss within the allowed
range.
2. The APs are easy to install.
3. APs are placed in a line. Co-channel
APs are far from each other, providing
good anti-interference capability.
1. The last row of seats is near the ceiling.
APs are within reach of the audience. In
this situation, AP protection boxes are
required.
2. If the stand depth is large, customers need
to deploy APs in other modes to enhance
signal coverage.
Overhead
1. APs are easy to install on ceilings with
bridleways.
2. APs and terminals are visible to each
other in line-of-sight distance, with
penetration loss within the allowed
range.
1. It is difficult to install APs on high ceilings
with simple structure.
2. Channel planning must take all APs
around into consideration. This mode has
poor anti-interference capability.
Floor
1. AP signals attenuate due to obstacles.
The AP coverage area can be
controlled. Therefore, many APs can
be deployed to connect more users.
2. APs are deployed at the rear of the
stand, invisible to the audience.
Obstacles between the stand and terminals
are complex; therefore, signal attenuation is
hard to estimate.
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 22
AP Capacity Design
AP capacity calculation process:
Service type
Total number of
users & Percentage
of concurrent users
Average
bandwidth
required
Number of
concurrent
users
Select
"Bandwidth-AP
concurrent
user" model.
N
Calculate the
number of APs
required.
Y
Design drawings
& site surveys
Stand size
Determine
distance
between APs:
>7.5 m
Add new coverage modes
and re-calculate the results.
Provide the results:
1. AP location
2. AP quantity
3. Number of users covered
by each AP
4. Percentage of concurrent
users
5. AP concurrent userBandwidth-Distance model
Example:
Based on customer requirements, calculate the average bandwidth required by each user: 300-500 kbps.
Based on the required bandwidth and terminal frequency distribution (2.4 GHz: 5 GHz = 1:1), select the model "400 kbps —— 50
concurrent users on each AP".
If the total number of users on the first layer of the south stand is 6330 and percentage of concurrent users is 20%, the total number of
users that concurrently use Wi-Fi services is 1266 (6330 x 20% = 1266). And a total of 25 APs are required (1266/50 = 25).
As observed from the drawing, the stand is 120 m long.
If all the APs are deployed in side mode (four channels are available), AP distance is 4.8 m (120/25 = 4.8), which is smaller than 7.5 m.
Interference may be serious.
Add a new AP deployment mode: overhead. Two rows of APs provide signal coverage at the same layer. AP distance is 9.2 m (120/13 =
9.2 m), which meet capacity requirements of the model "400 kbps-50 concurrent users on each AP".
Results:
1. AP location: above the seats in the last row and on ceiling
2. AP quantity: 26 in total, with13 for each row
3. Number of users covered by each AP: 6330/26 = 243
4. Final capacity model: Number of concurrent users on each AP—— Bandwidth —— Distance = 50 —— 400 kbps —— 9.2 m
5. Percentage of concurrent users: 26 x 50/6330 = 20.54%
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 23
AP Capacity Design (''Bandwidth-AP Distance-Number of
Concurrent Users on Each AP" Reference Table)
Data in the mapping relationship table is being tested.
Currently, the following typical data is available.
Assume four 2.4 GHz channels are available.
AP distance: 7.5 m
Number of concurrent users on each AP: 50 (2.4 GHz:5 GHz = 1:1)
Average bandwidth per user: 300-500 kbps
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 24
Channel Design Principles
1. Determine the available channels at the local site.
Determine available 2.4 GHz channels. In counties that support channels 1-13, use channels 1, 9, 13, and 4
to increase the distance between co-channel APs if many APs need to be deployed.
Available channels vary in different countries and regions. Some countries or regions will reserve some
channels. Select channels based on the conditions at the local site.
In some countries or regions, available 5 GHz channels may differ in indoor and outdoor scenarios. Select
channels according to local standards.
2. Plan the channels.
AP channels should be properly planned to prevent interference. When planning AP channels, avoid interference from
existing signals, which is of great significance to ensure high access quality.
Overall channel planning rules: Co-channel and adjacent-channel APs should be deployed far from each other to
increase channel multiplexing efficiency. Additionally, interference between APs on the same layer or different layers
should be considered.
3. Example:
Second layer stand
CH9
CH 36
CH1
CH 44
CH13
CH 52
CH5
CH 60
CH9
CH 100
CH1
CH 108
CH13
CH 56
CH5
CH 104
CH9
CH 120
CH1
CH 136
CH13
CH 44
CH5
CH 52
CH13
CH 128
CH5
CH 116
CH9
CH 124
CH1
CH 132
First layer stand
CH13
CH 116
CH5
CH124
CH9
CH 132
CH1
CH 140
CH13
CH 40
CH5
CH 48
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
CH9
CH 64
CH1
CH 112
Page 25
Deployment of Access Switches
1. Ensure that the cable length from the access switch to APs does not exceed 80 meters (the cable length is not straight-line
distance between the switch and APs but calculated based on cabling rules).
2. Avoid heavy magnetic and electronic interferences on the sites where access switches are installed.
3. Ensure that reliable AC power supply is available on the sites where the access switches are installed.
4. Protect the switches from moisture and dust (purchase protection boxes according to environment situations).
5. Determine the number of access APs based on the number of switch interfaces, PoE power supply capability of the power
module, and AP power consumption (note that outdoor APs have high power consumption).
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 26
Cabling Rules and Power Supply Modes
Cabling Rules
1. Ensure that the cable length from the AP to the access switch does not
exceed 80 meters.
2. Reserve 5-meter length for cable adjustment.
3. Keep the network cables far away from electromagnetic field.
4. Obtain the customer's and property owner's approval on the cabling routes.
Power Supply Modes
1
PoE power supply for APs (preferred), in compliance with 802.3at
2
Local AC power supply (applicable to indoor APs in scenarios where AC
power supply is available)
PoE power supply
Local AC power supply
3
Power supply using a PoE adapter (applicable to scenarios where no
AC power supply is available)
Using PoE adapter
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 27
Contents
1
Project Preparation
2
Product Selection
3
Bandwidth Design
4
Deployment Design
5
Project Case
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 28
Stadium High-Density Coverage Project
High-density coverage project for XX stadium
Project Preparation:
The following table describes project requirements collected from customers.
Item
Requirement
Coverage area
Stands and corridors
Switch location
Wired aggregation point marked on the map
Onsite environment
There is no interference source onsite.
Terminal type
Phones and tablets
Service type
User distribution
Available channels
Web page browsing, social networking, and video playing (a few
requirements)
The number of users on the stand at each layer has been collected.
36, 40, 44, 48, 52, 56, 60, 64, 100,104, 108, 112, 116, 120, 124,
128,132, 136, 140
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 29
AP Deployment at the Second Layer Stand
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 30
AP Deployment at the Second Layer Stand
…
…
9m
First row of APs:
Total distance: 650 m
Number of APs required:
650 m/9 = 72
Second row of APs:
Total distance: 580 m
Number of APs required:
580 m/9 = 64
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 31
Access Switch Deployment at the Second Layer Stand
…
Ensure that the distance between the
AP and switch is smaller than 80 m.
Maximum power consumption of each
AP: 25 W
Maximum output PoE power of an
access switch: 380 W
Each access switch connects to 10 APs.
Number of access switches required:
(72 + 64)/10 = 14
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 32
Bandwidth and Capacity Design for the Second
Layer Stand
Total number of APs: 72 + 64 = 136
Total number of users: 28000
Based on the model "Bandwidth-AP distance-Concurrent users on each AP" and the
terminal type ratio (2.4 GHz:5 GHz = 1:1), each AP allows 45 concurrent users and
each user obtains a bandwidth of 300 to 500 kbps.
Number of concurrent users: 45 x 136 = 6120
Percentage of concurrent users: 6120/28000 = 21.85%
All users at the second layer stand can connect to the Wi-Fi network concurrently.
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 33
AP Deployment at the First Layer Stand
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 34
AP Deployment at the First Layer Stand
First row of APs:
Total distance: 545 m
Number of required APs:
545 m/9 = 60
…
…
Second row of APs:
Total distance: 500 m
Number of required APs:
500 m/9 = 55
9m
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 35
Access Switch Deployment at the First Layer Stand
…
Ensure that the distance between the AP
and switch is smaller than 80 m.
Maximum power consumption of each AP:
25 W
Maximum output PoE power of an access
switch: 380 W
Each access switch connects to 10 APs.
Number of access switches required:
(60 + 55)/10 = 12
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 36
Bandwidth and Capacity Design for the First
Layer Stand
Total number of APs: 60 + 55 = 115
Total number of users: 23000
Based on the model "Bandwidth-AP distance-Concurrent users on each AP" and the
terminal type ratio (2.4 GHz:5 GHz = 1:1), each AP allows 45 concurrent users and
each user obtains a bandwidth of 300 to 500 kbps.
Number of concurrent users: 45 x 115 = 5175
Percentage of concurrent users: 5175/23000 = 22.5%
All users at the first layer stand can connect to the Wi-Fi network concurrently.
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 37
Signal Coverage in Corridors
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
AP Model
Quantity
Switch
AP 6010DN
46 x 2
6x2
Page 38
Bandwidth Design for Corridors
Total number of APs: 46 for each floor
Total area of each corridor: 5860 m2
Number of users per square meter: 1.2
Total number of users: 7032
Based on the model "Bandwidth-AP distance-Concurrent users on each AP" and the
terminal type ratio (2.4 GHz:5 GHz = 1:1), each AP allows 45 concurrent users and
each user obtains a bandwidth of 300 to 500 kbps.
Number of concurrent users: 45 x 46 = 2070
Percentage of concurrent users: 2070/7032 = 29.43%
All users in the corridors can connect to the Wi-Fi network concurrently.
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 39
Material List
Location
Number
of seats
Second
layer
stand
28000
First layer
stand
23000
Total
51000
AP Location
AP6510DN
Ant1
Ant2
First row
72
72
72
Access
Switch
RF
Cable
Attenuator
288
144
256
128
240
120
220
110
1004
502
14
Second row
64
64
64
First row
60
60
60
12
Second row
55
55
55
-
251
251
251
Location
AP6010DN
Access Switch
Indoor corridor
(second floor)
46
6
Indoor corridor (fifth
floor)
46
6
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
26
Page 40
Material Statistics
Material
Type
Quantity
Backup
AP6510DN
251
25
AP6010DN
92
9
Ant1
251
25
Ant2
251
25
AC
AC6605
8
-
RF cable
RF Cable-3 m
1004
52
Attenuator
Attenuator-15 dB
502
50
Access switch
S5700-28P-PWR-LI-AC
38
AP
Antenna
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Page 41
Thanks
www.huawei.com
Page 42
HUAWEI TECHNOLOGIES CO., LTD.
保密材料,注意发放范围
Appendix: Network Planning Support Channel
Network planning solution
In China:
Front-line
personnel
Enterprise
Networking
Professional
Services
HQ
Zhengxiaodong
58904
Zhaoyawei
69768
Outside China:
Front-line
personnel
Enterprise
Networking
Professional
Services
HQ
Xuzhi
00159508
COPYRIGHT ©2006 HUAWEI TECHNOLOGIES CO., LTD.
Zhaoyawei
69768
Page 43