Transcript Slide 0
AHAM--Household Appliance Sustainability Standards 2012 Energy Use per Unit Volume (GJ/m3) Why is AHAM developing sustainability metrics? As home appliances become more energy efficient, relatively speaking, the proportion of environmental impacts from other attributes are increasing. We need to broaden the conversation beyond just energy. Source: Boustani et al. (2010). Appliance Remanufacturing and Energy Savings 1 Refrigerator/Freezer Annual Energy Consumption 1400 1200 kWh/yr. 1000 800 600 400 200 0 1980 1990 1991 1992 1993 1994 1995 1996 1997 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 This is but one example of the tremendous gains in energy efficiency by appliances over the last 30 years. Isn’t just one measurement or attribute enough? Energy Star is largely a single attribute certification program for energy efficiency Multi-attribute standards are now the expectation Government procurement • Buildings – LEED • Computers – EPEAT • Office furniture – BIFMA Retailers • Walmart Supplier Sustainability Assessment • Kohl’s Department Store Reports 3 The Intersection of Many Ideas Standards Organizations • UL Environment, CSA, Good Housekeeping, and Green Seal developing sustainability standards in other sectors • Interested in appliances Retailers Government •“Manufacturers should take steps to measure and address sustainability” •EPA Energy Star writing sustainability measures in electronics sector •Green Guides •Gov’t Procurement Create business value •AHAM has the technical leadership and understanding of its products to develop sustainability measurements. 4 AHAM has partnered with the experts Recognized expertise in developing sustainability standards Contributing in-house LCA and toxicology expertise Credible, recognized expertise in the environmental sector Contributing stakeholder review and document management functions Internationally recognized sustainability consulting firm Contributing project management and liaison with key stakeholders 5 Target Audiences We recognize any standards must be available and will be relevant to many target audiences. CONSUMERS MANUFACTURERS ENVIRONMENTAL NGO’s Several target audiences for the Sustainability Standards GOVT: DOE/EPA RETAIL TRADE/ BUILDERS 6 Standards Development – Streamlined Process (Collaborative) 7 Phase 1 Life Cycle Screening Define Scope and Elements Selected Stakeholder Input Phase 2 Develop Draft Standard Stakeholder Review Draft Standard Available for Internal Use Phase 3 Pilot Test the Standard Phase 4 Incorporate Lessons from Pilot Testing Publish Standard Phase 5 Form Consensus Stds Committee (ANSI, SCC) Publish Final Consensus Standard Standards Development – Progress to Date Refrigeration Release Standard 8 Portable & Floor Care Released 2012 Release Standard Final Stakeholder Review Final Stakeholder Review Pilot Testing Pilot Testing Drafting Standard Drafting Standard Stakeholder Review of Scoping Document Stakeholder Review of Scoping Document Development of Standards Methodology Development of Standards Methodology Research Research Organization Organization Standards Development – Progress To Date Conventional Cooking Clothes Washer Release Standard Release Standard Final Stakeholder Review Final Stakeholder Review Pilot Testing Pilot Testing Drafting Standard Drafting Standard Stakeholder Review of Scoping Document Development of Standards Methodology Research Organization 9 Stakeholder Review of Scoping Document Development of Standards Methodology Research Organization Commenced Nov. 2012 Selected Stakeholder Input Priority stakeholders we have engaged include representative from the following organizations: The Sustainability Consortium EPA Sustainability Office EPA ENERGY STAR Environment Canada Individual Retailers Lowes, Sears-Kenmore, Best Buy, Kohl’s Consumers Union Environmental Defense Fund Carbon Disclosure Project 10 Scope of Standards The AHAM sustainability standards will cover household appliances. In major appliances, we will utilize the definitions and scopes of the coverage of products under 10 CFR 430, the U.S. Department of Energy, energy efficiency standards for appliances. The Portable and Floor Care Appliance Sustainability Standard will encompass over 70 different types of electrical small appliances in the following areas: Kitchen Countertop motorized and heating appliances Beverage appliances Garment care appliances Home environment portable appliances Personal care portable appliances Floor care appliances 11 Multiple Steps in Standards Processes Life Cycle-Based Research Develop value-chain initial heat-map Existing LCA Reviewed PCR’s, government studies, company studies, academic studies Coordinated with environmental impact reports Conduct generic LCA based on ISO 14064 Interview stakeholders Refine Hot Spot Analysis Multi-Attribute Approach The methodology for developing the Home Appliance Environmental Performance Standard is multi-attribute because it addresses an array of environmental and human health considerations. The multi-attribute approach was developed using a combination of life cycle assessment (LCA) information, literature sources, and input from a broad spectrum of key stakeholders. By starting with refrigeration products, we established a procedure, utilized multi-attribute methodology, identified unique North American parameters, and set the stage for other appliances. 13 Life Cycle Hot Spot Methodology 14 Life Cycle Hot Spot Methodology 15 An example of a Life Cycle Screening (“Hot Spots”) Life Cycle Stages Sustainability Impact Category Air Climate Change Living Resources (Flora & Fauna) Non-Living Resources Water (Quality & Quantity) Human Health Socioeconomic Raw Mat’ls Mfg Refrigerant ODP Releases during mfg Refrigerant Blowing Agent Packaging/ Distribution Hazardous waste Recycled content Solid waste Releases in supply chain Releases during mfg End-of-Life Noise Transport to recycling? Refrigerant Releases during mfg Hazardous waste Use Energy Foam High Priority Recyclability/ content of pkg Med. Priority Low Priority Materials of concern Continued use of fridge Review of Hotspots drives attributes and criteria selection and weighting. 16 Framework for Development of Standard Informed by Requirements of Standard Criteria Metric A characteristic of a product or process that has a direct influence on environmental performance The requirements for a product to meet the standard Quantification of the criteria that can be measured e.g. e.g. e.g. Avoid materials of concern Conformance with a central list of restricted materials Analytical test data demonstrating compliance Promote use of recycled materials 5-10% recycled content Documentation of calculation 17 Demonstration that specified requirements are fulfilled Materials Manufacturing & Operations End-of-Life Management Principles Conformity Assessment Attribute Energy during Use Life Cycle Screening Assured by Innovation Prerequisites Each of the six Attributes may have one or more prerequisites that are required as the minimum performance level. Products shall meet all prerequisites in a particular attribute section in order to be eligible for evaluation using the points system in that attribute section. If a product does not meet one or more of the prerequisites in a particular attribute section, it cannot be evaluated against that attribute. The product may still be assessed and receive points against the other attributes provided their associated prerequisites are met. 18 Major Attributes Each of our sustainability standards may draw from attributes such as: Materials Energy & Water during the use phase Manufacturing and Operations Product Performance End of Life Consumables Innovation 19 Innovation The intent is to award activities that exhibit exceptional performance above and beyond the requirements of this standard as well as activities that are not covered by the criteria within these requirements. The product is evaluated based on the following criteria: Innovation in product features and manufacturer programs and policies that demonstrate environmental performance improvement that is exceptional, measurable and beyond the requirements and criteria covered within this standard. 20 Standards breakdown Each of the product sustainability standards attributes are then broken down into criteria For example, the materials attribute may be broken into such areas as: Substances used in the product’s design Special substances, such as refrigerants and foam blowing agents in cold products Product recycled content Packaging recycled content Optimized use of raw materials The refrigeration standard has 19 criteria 21 Benefits of the standards Through a life-cycle approach, we can show the relative balance of environmental impacts of appliances across the attributes and criteria. Manufacturers can use these standards to measure existing and design future products Retailers, customers, procurement officials, and consumers know that the standards are based on a systematic approach using recognized methodologies and principles. 22 Next steps in Standards Complete collaborative standards development Allow companies to use the standards Form consensus standards committees Ballot and complete ANSI and SCC processes Refrigeration products Portable & Floor Care appliances Clothes Washers Others Stay tuned There is more coming… 24 Questions? For more information, please contact: Sriram Gopal Policy Analyst Association of Home Appliance Manufacturers 1111 19th St. NW, Suite 402, Washington, DC 20036 Tel: 202.872.5955, ext. 306 Email: [email protected] Thank you for your time. 25