Transcript Slide 1

‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
WATER-The Substance of Life
• Limits Kinds and Amounts of
Vegetation on Earth
• Limits Growth of Cities and Kinds of
Industry
Isfahan University of Technology
EARTH’S WATER SUPPLY
70% of Earth’s Surface
covered by water
97% of Earth’s water supply
in oceans
Ice at Polar Caps next most
abundant supply (>2%)
Groundwater next most
abundant supply (~0.5%);
approximately 50% of ground
water is > 0.5 miles deep
Fresh water in lakes, ponds
and streams ~0.008%
Soil and atmospheric water
~ 0.001%
Biological water ~0.0001%
Average annual rainfall on land
~ 30 inches
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Precipitation
Soil-Air
Interface
Vadose Zone
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Evaporation
Portion of aquifer where
pore spaces are occupied
with water and air
(unsaturated zone)
Applications of soil physics are crucial to sustainable use
of natural resources for agricultural and other land uses
Soil-Water
Interface
Capillary fringe zone
Ground water
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
‫تبخیر و تعرق‬
‫نزوالت جوی‬
‫آبیاری‬
‫نفوذ‬
‫ذخیره در خاک‬
‫نفوذ عمقی‬
‫عمق خاک‬
‫‪Isfahan University of Technology‬‬
Precipitation/Evaporation
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
• P/E>0.75= Humid (Forests)
• P/E >0.5= Sub-Humid (Mixed Forest
and Grasslands)
• P/E >0.25= Semi-Arid (Mixed
Grasslands and Semi-Deserts)
• P/E <0.25= Arid (Deserts)
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Soil Water Relationships
Isfahan University of Technology
• Bulk Density (b)
Ms
b 
V
b
3
– b = soil bulk density, g/cm
– Ms = mass of dry soil, g
– Vb = volume of soil sample, cm3
• Typical values: 1.1 - 1.6 g/cm3
• Particle Density (p)
Ms
p 
Vs
– P = soil particle density, g/cm3
– Ms = mass of dry soil, g
– Vs = volume of solids, cm3
• Typical values: 2.6 - 2.7 g/cm3
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
• Porosity ()
volume of pores

volume of soil

b 
  1  100%
p 

• Typical values: 30 - 60%
Isfahan University of Technology
‫حاج عباسی‬
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Water in Soils
• Soil water content
Mw
m 
Ms
– Mass water content (m)
– m = mass water content (fraction)
– Mw = mass of water evaporated, g
(24 hours @ 105oC)
– Ms = mass of dry soil, g
Isfahan University of Technology
‫حاج عباسی‬
• Volumetric water content (v)
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Vw
v 
Vb
V = volumetric water content (fraction)
Vw = volume of water
Vb = volume of soil sample
At saturation, V = 
V = As m
As = apparent soil specific gravity = b/w
(w = density of water = 1 g/cm3)
– As = b numerically when units of g/cm3 are used
–
–
–
–
–
–
• Equivalent depth of water (d)
– d = volume of water per unit land area = (v A L) / A = v L
– d = equivalent depth of water in a soil layer
– L = depth (thickness) of the soil layer
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Volumetric Water Content & Equivalent Depth
‫حاج عباسی‬
(cm3)
Equivalent Depth
(g)
Isfahan University of Technology
(g)
(cm3)
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Volumetric Water Content &
Equivalent Depth
‫حاج عباسی‬
Typical Values for Agricultural Soils
Soil Solids (Particles): 50%
0.50 in.
1 in.
Very Large Pores:
(Gravitational Water)
Total Pore
Space: 50%
Isfahan University of Technology
15%
0.15 in.
Medium-sized Pores: 20%
(Plant Available Water)
0.20 in.
Very Small Pores:
(Unavailable Water)
0.15 in.
15%
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Water-Holding Capacity of Soil
‫حاج عباسی‬
Effect of Soil Texture
Coarse Sand
Silty Clay Loam
Dry Soil
Gravitational Water
Water Holding Capacity
Available Water
Unavailable Water
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Soil Water Content
Soil Moisture Content
Water that may be evaporated from soil by heating at 1050C to a
constant weight
mass of water evaporated (g)
Gravimetric moisture content (w) =
mass of dry soil (g)
volume of water evaporated (cm3)
Volumetric moisture content () =
volume of soil (cm3)
= w*
bulk density of soil
density of water
3
cm
g

3
cm
g
g
3
cm 3  g g cm
g
g cm 3 g
cm 3
mass of dry soil (g)
Bulk density of soil () =
volume of soil (cm3)
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Soil Moisture Content: Methods of Measurement
1. Difficulties encountered for accurate moisture measurement in the
field:
2. Soils are highly variable
3. Soil moisture is highly dynamic (spatial temporal variability)
4. Plant water uptake is highly variable depending upon the stage of
growth
5. State of growth is again dependent upon nutrient application, water
availability, pests etc.
6. Chemicals present in the soil can make measurements unreliable
7. Costs involved
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Methods for soil water content
Direct method (Gravimetric;
Thermogravimetric)
Electrical
properties
Indirect methods
Radiation
technique
Acoustic
method
Thermal
properties
Chemical
methods
-Neutron scattering
g- ray attenuation
Electrical
Conductance
- Gypsum
blocks
- Nylon blocks
- Change in
conductance
Isfahan University of Technology
Dielectric constant
Methods of soil water
content determination
TDR
Principles underlying different methods of
assessment of soil water content
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
DIRECT
Gravimetric: evaporating water at 1050C.
Thermogravimetric: Soil sample is weighted and saturated with alcohol
and burned several times until a constant dry weight is obtained
INDIRECT
Electrical Conductance
Isfahan University of Technology
DIRECT
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Gravimetric: evaporating water at 1050C.
Feel Method:
Thermogravimetric: Soil sample is weighted and saturated with alcohol
and burned several times until a constant dry weight is obtained
Advantages: ensures accurate measurements, not dependent on
salinity and soil type, easy to calculate
Disadvantage: destructive test, time consuming, inapplicable to
automatic control, must know dry bulk density to transform data to
volume moisture content, inaccurate because of soil variability
There are many classifications for soil types and major differences
within each classification
Soil management can have a major impact upon these soil properties.
Compaction is the major cause of error in bulk density.
Isfahan University of Technology
http://edis.ifas.ufl.edu/
Frequency Domain Reflectometry: radio
frequency (RF) capacitance techniques
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Actually measures soil capacitance
A pair of electrodes is inserted into the soil
Soil acts as the dielectric completing a
capacitance circuit, which is part of a
feedback loop of a high frequency
transistor oscillator
As high frequency radio waves (about
150 MHz) are pulsed through the
capacitance circuitry, a natural resonant
frequency is established which is
dependent on the soil capacitance,
which is related to the dielectric constant
by the geometry of the electric field
established around the electrodes
Two commercially available instruments
using this technique: the Troxler Sentry
200-AP probe and the Aquaterr probe
Isfahan University of Technology
Time Domain Reflectometry (TDR): , 28 s
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
The soil bulk dielectric constant (K) is determined by measuring the
time it takes for an electromagnetic pulse (wave) to propagate along a
transmission line (L) that is surrounded by the soil
Since the propagation velocity (v) is a function of K, the latter is
therefore proportional to the square of the transit time (t, in seconds)
down and back along the L
K = (c/v)2 = ((c.t)/(2.L))2
where c is the velocity of electromagnetic waves in a vacuum (3•108 m/s
or 186,282 mile/s) and L is the length embedded in the soil (in m or ft)
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
 TDR determinations involve measuring the propagation of
‫حاج عباسی‬
electromagnetic (EM) waves or signals
 Propagation constants for EM waves in soil, such as velocity and
attenuation, depend on soil properties, especially  and EC
The propagation of electrical signals in soil is influenced by q and EC
The dielectric constant, measured by TDR, provides a good measurement
of this soil water content
Disadvantage: Costly, not really independent of salt content
Isfahan University of Technology
Time Domain Transmission (TDT)
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
This method measures the one-way time
for an electromagnetic pulse to propagate
along a transmission line (L). Thus, it is
similar to TDR, but requires an electrical
connection at the beginning and ending
of the length.
Notwithstanding, the circuit is simple
compared with TDR instruments.
Disadvantages: Reduced precision, because the generated pulse is
distorted during transmission; soil disturbance during installation; needs
to be permanently installed in the field
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
NUCLEAR TECHNIQUES: Neutron Scattering, , 1 to 2 min ‫حاج عباسی‬
With this method, fast neutrons emitted from a radioactive source are
thermalized or slowed down by hydrogen atoms in the soil
Since most hydrogen atoms in the soil are components of water
molecules, the proportion of thermalized neutrons is related to 
Advantages: can measure a large soil volume,
can scan at several depths to obtain a profile of
moisture distribution, nondestructive, water can
be measured in any phase
Disadvantages: high cost of the instrument,
salinity, must calibrate for different types of
soils, excess tube, radiation hazard,
insensitivity near the soil surface, insensitivity to
small variations in moisture content at different
points within a 30 to 40 cm radius, and variation
in readings due to soil density variations (error
rate of up to 15 percent)
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Gamma Attenuation: volumetric water content, < 1 min
‫حاج عباسی‬
 This method assumes that the scattering and absorption of gamma
rays are related to the density of matter in their path
 The specific gravity of a soil remains relatively constant as the wet
density changes with increases or decreases in moisture
 Changes in wet density are measured by the gamma transmission
technique and the moisture content is determined from this density
change
Advantages: can determine mean water content with depth, can be
automated for automatic measurements and recording, can measure
temporal changes in soil water, nondestructive measurement
Disadvantages: restricted to soil thickness of 1 inch or less, but with
high resolution, affected by soil bulk density changes, costly and
difficult to use, large errors possible when used in highly stratified soils
Isfahan University of Technology
Soil and Water
evaporation
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
WATER CONTENT
 LIQUID
• Gravimetric
(Mass/Mass)
• Volumetric
(Volume/Volume)
• Relative
 VAPOR
• Concentration
(Mass/ volume air)
• Pressure
(KPa)
• Relative Humidity
USES of WATER
in PLANTS
•
•
•
•
•
1. Constituent
2. Solvent
3. Reactant-product
4. Turgidity
5. Temperature Control
CONSTITUENT
• Water constitutes more than 70% of fresh
weight of most plants (Seeds are
exception)
• Between 60-90% of the water is contained
in the plant cell providing both biological
and physical functions.
• The remaining 10-40% is contained as
liquid in cell walls providing a continuum
between the soil supply and the living cell.
SOLVENT
• Dissolves both organic and inorganic
constituents essential for life
• Dissolves gases-CO2
REACTANT-PRODUCT
• Photosynthesis
CO2+ H2O = SUGAR
• Respiration
CH2O + O2 = CO2 + H2O
ENERGY BALANCE
• Evaporation dissipates heat
• Condensation-precipitation releases
heat
• Amount of water passing through
plants as transpiration depends on
environment and species
Wheat 1000 kg H2O per kg dry matter
Cotton 5000 kg H2O per kg lint
‫رابطه آب خاك و گیاه‬
1 mole water ~ 18 cm3 contains 6.02 x 1023 molecules
‫تكمیلی‬
1 cm3 ~ 3.3 x 1022 (33 thousand billion billion) ‫حاج عباسی‬
Consider a beach 1.6 x 106 m (1000 miles) long
200 m (656 feet) wide
100 m (328 feet) deep
Volume beach = 3.2 x 1010 m3 sand
Assume that each grain = a sphere 1 mm diameter
With loose packing 109 (one billion) grains in 1 m3
Entire beach 3.2 x 1019 sand grains, 1000 < number
of molecules in 1 cm3 water
It would take 1000 beaches to contain as many sand
grains as molecules in 1 cm3 of water
Each water molecule is ~ 3 A (3 x 10-10 m)
It would take 33 x 106 layers to form a layer
of water 1 cm deep.
UNIQUE PROPERTIES
of WATER
g+
H
g+
105O
O
g-
H
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Hydrogen bond
H+
H2O
=
O--
+
-
H+
Gives structural strength
Bond depends on temperature:
Higher is the temperature weaker is bond
Positive end attraction with -ve end of other water molecules
Isfahan University of Technology
‫رابطه آب خاك و گیاه‬
‫تكمیلی‬
‫حاج عباسی‬
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Hydrogen
Electro positive
‫حاج عباسی‬
Hydrogen
H-O : 0.97 A
1050
H-H : 1.54 A
Polarity
Oxygen
Negative
Symmetrical
Isfahan University of Technology
angstroms
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Polymer type of grouping
‫حاج عباسی‬
H+
H+
O-
Cations: Na+, K+, Ca2+ : become hydrated through their
attraction to the Oxygen
Anions or negatively charged clay surfaces: attract water
through hydrogen
Isfahan University of Technology
‫رابطه آب خاك و گیاه‬
‫تكمیلی‬
‫حاج عباسی‬
Some definitions
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Adhesion - the attraction or clinging together of unlike substances
Cohesion - the attraction of a substance for itself; the mutual attraction among
molecules or particles comprising a substance tat allows it to cling together as a
continuous mass.
absorption - the process by which one substance is taken into and included
within another substance, as the absorption of water by soil or nutrients by
plants.
adsorption - the increased concentration of molecules or ions at a surface,
including exchangeable cations and anions on soil particles.
flickering clusters refers to the quasicrystalline state of water molecules while
in a liquid state. The molecules associate and dissociate repeatedly in
transitory or flickering polymer groups. Water molecules are attracted to one
another due to the hydrogen bonding that takes place between the negatively
charged end of the oxygen atom in the molecule and the positively charged
ends of hydrogen atoms in adjacent water molecules.
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
heat of fusion (ice) The amount of energy required to turn a liquid‫عباسی‬
into
‫حاج‬a solid.
heat of vaporization The amount of energy required to turn a liquid to a vapour
(to overcome the attractive forces between adjacent molecules in a liquid).
dipole moment a measure of the tendency of a polar molecule to be affected
by an electrical or magnetic field (i.e., NMR - Nuclear magnetic resonance)
Volumetric heat capacity is the change in the heat content of a unit volume per
unit change in temperature.
Specific heat is the change in the heat content of a unit mass per unit change in
temperature.
surface tension A molecule at the surface of a liquid is not completely
surrounded by other molecules of the liquid. The forces acting upon it are
unbalanced, with the result that it experiences a stronger attraction into the
body of the liquid (cohesion) rather than into the less dense gaseous phase.
This unbalanced force draws the surface molecules inward with and results in
the tendency for the surface to contract and the molecules to be slightly denser
Isfahan University of Technology
at
the surface.
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
sublimation the direct transition from the solid state to the vapor state
hydrophobic water repellent
capillary attraction - a liquid's movement over or retention by a solid
surface due to the interaction of adhesive and cohesive forces.
capillary fringe a zone just above the water table that is maintained in an
essentially saturated state by capillary forces of lift.
viscosity (centipose, cP, N s m-2 x 10-3, kg m-1 s-1). When a fluid is moved
in shear (that is to say, when adjacent layers are fluid are made to slide over
each other), the force required is proportional to the velocity of shear.
Viscosity is the proportionality factor. It is the property of the fluid to resist
the rate of shearing and can be visualized as an internal friction. Fluids of
lower viscosity flow more readily. Thus oil has a higher viscosity than water.
Fluidity is the reciprocal of viscosity. Viscosity is the preferred term.
Isfahan University of Technology
‫رابطه آب خاك و گیاه‬
‫تكمیلی‬
‫حاج عباسی‬
Cohesive – forces of attraction between like
molecules.
At an air-water interface – surface tension.
Adhesion – attraction of one substance for a
substance of another kind.
Tensile strength – work that must be done to
create or extend a new or
larger surface.
Viscosity – resistance to flow.
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
If water were an ordinary compound whose molecules are
subject to weak forces, its boiling and freezing point
would fall below hydrogen sulfide
Strong hydrogen bonding between water molecules
prevents this
Water occurs in all three states (solid, liquid, and gaseous)
at prevailing temperatures on the earth’s surface
Example: Ice cubes in a glass at room temperature
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Why water wets clean glass?
‫حاج عباسی‬
 Surface of glass has O and unpaired electrons
 Water molecules form hydrogen bond
 Force stronger than gravity
Why water does not stick to glass surface coated
with grease?
 Surface of grease has no O and free electrons
 Water molecules cannot form hydrogen bond
 Therefore, water do not stick
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Forces acting on a water molecules ‫حاج عباسی‬
Air-water
Interface
Air
At point A:
A
Attraction of air for water
molecules is much less
than that of water
molecules for each other.
B
At point B:
Forces acting on
water molecule
are equal in all
direction
Water
Consequently, there is a net downward force on the
surface molecules, and result is something like a
compressed film at the surface. This phenomenon is
called surface tension
Isfahan University of Technology
Surface Tension
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
The cohesive forces between liquid molecules are responsible for
the phenomenon known as surface tension
The molecules at the surface do not have other like molecules on all
sides of them and consequently they cohere more strongly to those
directly associated with them on the surface. This forms a surface
"film" which makes it more difficult to move an object through the
surface than to move it when it is completely submersed.
 Surface tension is typically measured
in dynes/cm. The force in dynes
required to break a film of length 1 cm
 Equivalently, it can be stated as
surface energy in ergs/cm2
 Water at 20°C has a surface tension
of 72.8 dynes/cm compared to 22.3
for ethyl alcohol and 465 for mercury
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Contact Angle
‫حاج عباسی‬
 Solid
 Liquid
 Gas
Liquid and gas (air) in contact with solid
Interface between air and water forms a definite angle
“contact angle”
g sa  g sw
cos a 
g wa
Young’s
equation
gsa > gsw; cos a = + or a <
900
Angle of contact is acute in a
liquid that wets the solid
L
Air
Solid
L
Angle of contact is obtuse
(between 90 and 180) in a liquid
that does not wet the solid
Isfahan University of Technology
Air
Solid
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Hydrophilic Versus Hydrophobic Soils
‫حاج عباسی‬
When the adhesive forces between water molecules and an object
are weaker than the cohesive forces between water molecules, the
surface repels water and is said to be hydrophobic. Hydrophobic soils
restrict the entry of water, which 'balls up' or sits on the soil in beads
rather than infiltrating the soil.
Hydrophobic soils exhibit an obtuse (greater than or equal to 90o)
wetting angle that causes capillary repulsion, so preventing water
from entering soil pores
Hydrophilic or normally wettable soils display an acute (less than 90o)
angle of contact with water, allowing infiltration. adhesive forces
between water molecules and an object are stronger than the
cohesive forces between water molecules
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Capillary Fundamentals and Soil Water
Cohesion: Attraction of molecules for each other
Adhesion: Attraction of water molecules for solid surfaces
By adhesion, solids hold water
molecules rigidly at their soil-water
surface
By cohesion water molecules
hold each other away from solid
surfaces
Together it is possible for soil solids to
retain water and control it’s movement
Isfahan University of Technology
Gravity
Capillary
‫حاج عباسی‬
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
The dipolar interaction between water
molecules represents a large amount of
internal energy (the energy associated
with the random, disordered motion of
molecules) and is a factor in water's
large specific heat (the amount of heat
per unit mass required to raise the
temperature by one degree Celsius).
The dipole moment of water provides a
"handle" for interaction with microwave
electric fields in a microwave oven.
Microwaves can add energy to the water
molecules, whereas molecules with no
dipole moment would be unaffected.
Isfahan University of Technology
Dipolar Bonding in Water
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Water rises in the capillary against the force of gravity
‫حاج عباسی‬
!!!! What happens if there is no force of gravity !!!!!
Water
Isfahan University of Technology
Water
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Capillary Mechanism
‫حاج عباسی‬
2 r1
Rise continues till:
Weight of water in the tube (force of
gravity) = Total cohesive and adhesive
forces
h1
2 r2
h2
Water
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
2 r‫حاج عباسی‬
Force of gravity = Mass of water column * Acceleration
= (volume of water * density) * g
= (p * r2* h) *dw * g …………(A)
Total cohesive and adhesive forces
h
= (perimeter) * surface tension
=2*p*r*g
At equilibrium:
…………(B)
Water
A=B
(p * r2* h) *dw * g = 2 * p * r * g
2 *g
h
r * dw * g
Isfahan University of Technology
use
Show
0.15
h
r
g = 72.75 dynes/cm
dw= 0.9982 g/cm3
g = 980 cm/s2
‫رابطه آب خاك و‬
If two principle radii r1 and r2‫گیاه تكمیلی‬
0.15
h
r
1 1
h  0.15  
 r1 r2 
This relationship tells us that:
Capillary Rise
 Capillary rise is higher in small pores
Isfahan University of Technology
‫حاج عباسی‬
r = 0.1 cm; h = 1.5 cm
r = 1.0 cm; h = 0.15 cm
r = 10 cm; h = 0.015 cm
Radius
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
The inverse relationship between height of rise of water and radius
of soil pores may not be always valid:
 Soil pores are not straight uniform openings as a tube
 Some soil pores may entrap air and slow down the capillary rise
Soil solids
Tortuous flow
paths of water
Entrapped air
water
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Capillary water
Adsorbed water
Enlarged soil
particles or
aggregates
Two forms of water in soil
Soil solids tightly absorb water
Capillary forces hold water in capillary pores
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
0.15
h
r
Height (cm)
Loam
Sand
Clay compacted
Time (days)
Isfahan University of Technology
Brady,1984
UNIQUE PROPERTIES
of WATER
TEMPERATURE RELATIONS
– Heat of Vaporization = 540 cal/g@100C
2.45 MJ/kg
– Heat of Fusion = 80 cal/g@0C
– Heat Capacity = 1.0 cal/g
– Thermal Conductivity = High
‫رابطه آب خاك و گیاه‬
‫تكمیلی‬
‫حاج عباسی‬
‫رابطه آب خاك و گیاه‬
‫تكمیلی‬
‫حاج عباسی‬
UNIQUE PROPERTIES
of WATER
 DENSITY
– 0.9998 g/cm3 at 0 oC
– 1.0 g/cm3 at 4 oC
– 0.9956 g/cm3 at 30 oC
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
Temperature range in liquid phase for H+ compounds
100
Boiling point
Freezing point
H2O (2+16=18)
Temperature (0C)
50
Hydrogen telluride
0
H2Te
Hydrogen sulfide
-50
H 2S
(130)
H2Se
(80)
Hydrogen selenide
(2+32=34)
-100
0
Isfahan University of Technology
50
Molecular Weight
100
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Does water swell and shrink with Temperature?
1
0.998
40 C
0.996
Density (g cm-3)
0.994
0.992
0.990
Temperature (0C)
-10
Isfahan University of Technology
0
10
20
30
40
50
‫حاج عباسی‬
‫رابطه آب خاك و گیاه‬
‫تكمیلی‬
‫حاج عباسی‬
‫رابطه آب خاك و گیاه‬
‫تكمیلی‬
‫حاج عباسی‬
UNIQUE PROPERTIES
of WATER
 SOLVENT
– Small Size
– Polar characteristics
– High Dielectric Constant
UNIQUE PROPERTIES
of WATER
 Transparent to Visible Radiation
(400-700nm)
 Highly Absorbent in Infra-Red
(>1000 nm)
UNIQUE PROPERTIES
of WATER
 HIGH SURFACE TENSION
– Adhesion
– Cohesion
– Tensile Strength
( >30MPa ~4000#/in2)
UNIQUE PROPERTIES
of WATER

IONIZATION
– Only 1 molecule out of 55 x 107 is
ionized
pH ~ - Log (H+)
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
‫مقایسه نقطه ذوب (‪ )MP‬نقطه جوش (‪ ) BP‬ووزن ملكولي (‪) MW‬‬
‫چندین ماده با آب‬
‫‪C4H30‬‬
‫‪5.5‬‬
‫‪251‬‬
‫‪198‬‬
‫‪C5H12 C6H16‬‬
‫‪-91‬‬
‫‪98‬‬
‫‪100‬‬
‫‪-130‬‬
‫‪36‬‬
‫‪72‬‬
‫‪C2H6‬‬
‫‪H20‬‬
‫‪NH3‬‬
‫‪-172‬‬
‫‪-36‬‬
‫‪30‬‬
‫‪0‬‬
‫‪100‬‬
‫‪18‬‬
‫‪-78‬‬
‫‪-33‬‬
‫‪17‬‬
‫‪CH4‬‬
‫‪MP -184‬‬
‫‪BP -161‬‬
‫‪MW 16‬‬
‫‪Isfahan University of Technology‬‬
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
100
‫حاج عباسی‬
75
Properties of Water
H2O actual
Centigrade (C)
50
Temperature range of water
and similar structured
molecules (from Leopold, 1966)
25
0
H2Te (129 g/mole)
-25
H2Se (80 g/mole)
-50
H2S (34 g/mole)
-75
H2O theory (18 g/mole)
-100
Fig. 1. Temperature range of various hydride groups.
Isfahan University of Technology
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
‫حاج عباسی‬
‫باوجوداینكه وزن ملكولي آب نسبتا كم است ولي مقاومت پیوند‬
‫هیدروژني وساختمان دروني آن باعث شده تا دردرجه حرارت طبیعي‬
‫بصورت مایع باشد نه بصورت بخاربدین معني كهعناصري با وزن‬
‫ملكولي تقریبا شبیه به آب در درجه حرارتهاي بسیارپایین ذوب مي‬
‫شوند ویابجوش مي آیند از طرف دیگر عناصردیگرباید وزن ملكولي‬
‫بسیارباالیي داشته باشند تا بتوانند دردرجه حرارتهاي ذوب یاجوش آب‬
‫ذوب یا بحالت جوش درآیند یعني آب درحالت مایع مانند ملكولهاي‬
‫بسیارسنگین عمل مي كند‪.‬‬
‫‪Isfahan University of Technology‬‬
COLLIGATIVE PROPERTIES
of
AQUEOUS SOLUTIONS
PROPERTY
PURE WATER 1.O M SOLUTION
1. Vapor Pressure 0.61 KPa@Oo Decreased according
101.3 KPa@100o
2. Boiling Point
100oC
3. Freezing Point
0oC
4. Osmotic Potential
0
5. Chemical Potential
0
to Raoult’s Law
100.52oC
-1.86oC
-2.27 MPa
Decreased
WATER VAPOR
TEMP
oC
CONCENTRATION
G M-3
MOLE FRACTION
PRESSURE
kPa
-10
2.358
0.00256
0.260
0
4.847
0.00603
0.611
10
9.399
0.01211
1.227
20
17.30
0.02307
2.337
30
30.38
0.04187
4.234
40
51.19
0.07281
7.378
50
83.06
0.1218
12.34
DRY AIR = 1. 205 Kg m-3
SATURATED AIR = 1.194 Kg m-3
Vapor pressure=4.62 x10-4 vdT
Wet bulb
Dew Point
RAUOLT’S LAW
e = eo Nw
Nw+Ns
e= Vapor Pressure of solution
eo= Vapor Pressure of pure water
Nw= moles of solvent
Ns= moles of solute
OSMOTIC PRESSURE
Van’t Hoff equation
 = NsRT
V
 = osmotic pressure in Mega Pascals
Ns= moles of solute
R= gas constant (0.0083 L MPa /mol @273o)
T= absolute temperature
V= volume of solvent in Liters
(RT= 2.272 @) 0oC &2.437 @ 20oC literMPamol-1)
CHEMICAL POTENTIAL
of WATER in a SOLUTION
A measure of the ability of WATER to
do work
Go = partial molal Gibb’s free energy
Go = -RTlnK (K = equilibrium constant)
A
B G Negative = Spontaneous
G Positive = Additional Energy
Required
CHEMICAL POTENTIAL
of WATER
µw-µwo = RT lnNw
µw= chemical potential of water in
solution (Jmol-1)
µwo= chemical potential of pure water
R= Gas constant = 8.314 J mol-1 K-1
T= Absolute temperature
Nw= mole fraction of water in solution-can
be replaced by ln e/eo
WATER POTENTIAL
(PRESSURE UNITS)
w = RT ln e/eo
V
w
The water potential of a solution is decreased by
those factors which reduce the vapor pressure
1. Addition of solutes (Osmotic)
2. Matric forces ( Interfacial Adhesive Forces)
3. Reduction in Temperature
4. Tension
WATER MOVEMENT
Flux Jw (moles per meter2 per second)
= Concentration Gradient
( -  mols/Distance; )
* Diffusion Coefficient (DW)
LIQUID STATE
• VAPOR STATE
• Potential Gradient
• Hydraulic
Conductivity
(Cells 7 x 10-13ms-1)
(Soil 10-2 – 10-10 m2 sec-1)
• Vapor Pressure
Gradient
• Diffusion Coefficient
(2.4 x 10-5 m-2s-1)
• Resistance
‫رابطه آب خاك و‬
‫گیاه تكمیلی‬
Forces that affect movement of water into the soil
‫حاج عباسی‬
Gravity: a constant force that pulls the water downward
Cohesion: attraction of water molecules for each other. It is the force that
holds a droplet of water together
Adhesion: attraction of water molecules to other substances. This force
causes water molecules to adhere to other objects, such as soil particles
Placing a drop of water on a piece of newsprint paper
Force of adhesion between the water molecules and the paper
molecules is greater than the force of cohesion that holds the water
molecules together
The water droplet spreads out and soaks into the paper
Placing a drop of water on a piece of waxed paper
Force of adhesion between the water molecules and the paper
molecules is lower than the force of cohesion that holds the water
molecules together
The water droplet remains intact
Isfahan University of Technology
TOTAL WATER POTENTIAL
 =  – (
W
p

+

m
W = Total Water Potential
p = Pressure Potential
 = Osmotic Potential
m = Matric Potential
g = Gravitational Potential
+
)
g
WATER POTENTIAL
SOIL SYSTEM
• Matric Forces
Surface Tension
Electrostatic
Association
• Osmotic
PLANT SYSTEM
• Surface Tension
• Cohesion
• Osmotic
• Pressure
DIFFUSION COEFFICIENTS
(10-5 M 2 S-1)
TEMPERATURE
oC
0
H2O VAPOR
CO2
2.13
1.33
10
2.27
1.42
20
2.42
1.51
30
2.57
1.60
40
2.72
1.70
‫رابطه آب خاك و گیاه‬
‫تكمیلی‬
‫حاج عباسی‬
Physical Properties of Water
l Liquid phases in soil and plant are similar
l In both systems the liquid is a solution of
water and dissolved substances
l
Physical properties of water