Transcript Flag Fire Training Kit USERS GUIDE

INTRODUCTION
TO NAVSEA TRAINING KITS
NAVSEA has developed and authorized standardized shipboard training aids to support
the new Damage Control Plotting Symbology in NSTM 079, Volume 2.
NAVSEA has developed a total of six flag training kits. Collectively 41 types of
damage or casualties are represented. The six kits consist of the Fire Kit, the Damage
Control Kit, the Main Space Kit, the Damage Control 2 Kit, the Structural Kit and the
CBR-D Small deck or the CBR-D Kit Large deck. The Fire, Damage Control and Main
Space kits have been in u
Note: This users guide is intended as a general instruction for the use of NAVSEA
issued training flags. It is not intended to as a scenario package replacing CNSF or
CNAF scenarios or drill packages.
HOW TO GET REPLACEMENT
KITS OR FLAGS
•
Replacement kits or flags can be purchased under GSA contract:
SIN 27-100 Training Devices
Contract Number GS-02F-0055U
The Slate River Corporation
[email protected]
For general guidelines in the use of NAVSEA Damage Control Training Kits. This
guide is only intended to assist the ships Damage Control Training Team in the
integration of Damage Control Training kit props into existing damage control
scenarios. Questions concerning, comments or suggestions for this guide or the
Damage Control Training kits should be sent to: [email protected]
The General Goals of the Damage
Control Casualty Flag Training Set
• Introduce new Damage Control symbology
• Standardize DC training props throughout the fleet
• Reduce workload on DCTT by reducing the time spent:
Planning and setting up drills
Training and retraining the crew on the meaning and purpose of each
training prop
Developing own props and relearning training props command to
command
Train crewmembers on system color-coding and future Advanced Damage
Control Software Systems Symbology
Reduce verbal disclosure.
CONCEPT OF OPERATION
All training flag have the same general concept of
operations of dividing the casualty into 3 phases.
Phase One: Report it (Size it up)
Phase Two: Engaged (Fight it)
Phase Three: No (Monitor it)
Phase One: Report it (Size it up)
The training flag is used alone or in
combination with other props to disclose the
casualty:
•
During this phase the DCTT evaluates
the emergency teams initial assessment
of the casualty. Once the DCTT has
observed enough actions it can move
onto the next phase.
Phase Two: Engaged (Fight it)
The training flag is used alone or in
combination with other props to disclose the
Engaged phase of the casualty:
•
During this phase the DCTT evaluates
the emergency teams actions to fight the
casualty. Once the DCTT has observed
enough actions it can move onto the next
phase.
Phase Three: No (Monitor it)
The training flag is used alone or in
combination with other props to disclose the
No phase of the casualty:
•
During this phase the DCTT evaluates
the emergency teams actions to monitor
the casualty. Once the DCTT has observed
enough actions it can move onto the next
phase.
DCTT Flag Procedures – How to Read and Use
1. D-Casualty
title abbreviation.
2. DCTT1-Hang the flag
DCTT2-Hold the flag
3. 030108-Date
Mar 01 2008
Casualty Title
Example photo
of flag use during
each phase of
the casualty
DCTT Guidance
for each
Casualty Phase
Directions for REPORTED Directions for ENGAGED
Phase of the casualty
Phase of the casualty
Directions for NO
Phase of the casualty
DCTT FLAG PROCEDURE
RUPTURE-CW
RCW-DCTT1-030108
SIZE IT UP
Casualty initial reports, assessment, evaluation
and information. What do I have?
FIGHT IT
Casualty engagement, What am
I doing to make progress
MONITOR IT
The fight is complete,
No further spread, Clean it up
Reported = (Size It Up)
Engaged = (Fight It)
No = (Monitor It)
1. Hang the flag by the straps provided with
the REPORTED ICON displayed in front.
2. For a ruptured pipe hang the flag on the
pipe itself. For a ruptured or leaking valve
hang the flag behind the valve if possible.
3. Drawing non-verbal attention to the rupture
flag can be achieved using the Sounds of
Damage, a LP air hose or water spray bottle.
4. Observe the trainee from 3 to 5 minutes to
“size up” the rupture.
5. Record all the actions of the trainee
including the time it takes the trainee to
discover and report the casualty.
6. It is not necessary for the trainee to
complete all the actions in the RCW check
list prior to to shifting the flag to the ENGAGED
phase of the casualty. Once the trainee
has completed or missed enough steps
to judge his or her proficiency move to
the ENGAGED phase.
1. Flip the flag to ENGAGED symbol.
The trainee(s) are now actively ENGAGING/
fighting the casualty.
2. It is nearly impossible to visually
determine the GPM flow of a ruptured pipe.
A more accurate measurement is the amount
of liquid accumulation on the deck or in the
bilge and its rate of rise or fall.
3. Lowering and raising the level of the flag
by hand or another indicating device can be
used to indicate the level of the liquid and
rate of rise or fall.
4. Observe the trainee(s) from 10 to 20
minutes to “fight” the rupture using the level of
the flag or other device to indicate progress.
5. Record all the actions of the trainee(s)
including the reports, type of repair, PPE,
tactics and organization.
6. It is not necessary for the trainee to
complete all the actions in the RCW check list
prior to to shifting the flag to the NO phase
of the casualty. Once the trainee has
completed or missed enough steps
to judge his or her proficiency move to
the NO phase.
1.Flip the flag to NO symbol. The trainee(s) are
now MONITORING/cleaning up the casualty.
2. Observe the trainee(s) from 5 to 10
minutes to “monitor” the rupture.
3. The trainee(s) should test the effectiveness
of repairs, dewater, remove hazards,
investigate for hidden and secondary damage.
4.The NO phase is also an opportunity to shift
back to ENGAGED to “re-rupture the pipe.
This can be used to indicate an improper
repair or failed action during the ENGAGED
phase causing the trainee(s) to re-trace their
steps.
5. Record all the actions of the trainee(s)
including the reports, methods of overhaul,
PPE, tactics and organization.
6. It is not necessary for the trainee to
complete all the actions in the RCW check list
prior to to completing the exercise. Once
the trainee has completed or missed
enough steps to judge his or her proficiency
secure and debrief the trainee(s).
7. Conduct an on station debrief immediately
to provide trainees (s) feed back and
correct errors.
SIZE IT UP
Casualty initial reports, assessment, evaluation
and information. What do I have?
Reported = (Size It Up)
Hang the flag by the straps provided with the
REPORTED ICON displayed in front.
FIGHT IT
Casualty engagement, What am
I doing to make progress
Engaged = (Fight It)
Flip the flag to ENGAGED symbol. The trainee(s)
are now actively ENGAGING/fighting the casualty.
MONITOR IT
The fight is complete,
No further spread, Clean it up
No = (Monitor It)
Flip the flag to NO symbol. The trainee(s) are
now MONITORING/cleaning up the casualty.