Transcript Chapter One: Introduction to Pipelined Processors

Principles of Linear Pipelining
Example : Floating Point Adder
Unit
Floating Point Adder Unit
• This pipeline is linearly constructed with 4
functional stages.
• The inputs to this pipeline are two normalized
floating point numbers of the form
A = a x 2p
B = b x 2q
where a and b are two fractions and p and q
are their exponents.
• For simplicity, base 2 is assumed
Floating Point Adder Unit
• Our purpose is to compute the sum
C = A + B = c x 2r = d x 2s
where r = max(p,q) and 0.5 ≤ d < 1
• For example:
A=0.9504 x 103
B=0.8200 x 102
a = 0.9504 b= 0.8200
p=3 & q =2
Floating Point Adder Unit
•
Operations performed in the four pipeline
stages are :
1. Compare p and q and choose the largest
exponent, r = max(p,q)and compute
t = |p – q|
Example:
r = max(p , q) = 3
t = |p-q| = |3-2|= 1
Floating Point Adder Unit
2. Shift right the fraction associated with the
smaller exponent by t units to equalize the
two exponents before fraction addition.
• Example:
Smaller exponent, b= 0.8200
Shift right b by 1 unit is 0.082
Floating Point Adder Unit
3. Perform fixed-point addition of two fractions
to produce the intermediate sum fraction c,
where 0 ≤ c < 1
• Example :
a = 0.9504 b= 0.082
c = a + b = 0.9504 + 0.082 = 1.0324
Floating Point Adder Unit
4. Count the number of leading zeros (u) in
fraction c and shift left c by u units to
produce the normalized fraction sum
d = c x 2u, with a leading bit 1. Update the
large exponent s by subtracting s = r – u to
produce the output exponent.
• Example:
c = 1.0324 , u = -1  right shift
d = 0.10324 , s= r – u = 3-(-1) = 4
C = 0.10324 x 104
Floating Point Adder Unit
• The above 4 steps can all be implemented
with combinational logic circuits and the 4
stages are:
1. Comparator / Subtractor
2. Shifter
3. Fixed Point Adder
4. Normalizer (leading zero counter and shifter)
4-STAGE FLOATING POINT ADDER
A = a x 2p
a
b
Stages:
S1
B = b x 2q
A
Other
fraction
Exponent
subtractor
B
Fraction
selector
Fraction with min(p,q)
r = max(p,q)
t = |p - q|
Right shifter
Fraction
adder
c
S2
r
Leading zero
counter
S3
c
Left shifter
r
d
S4
Exponent
adder
s
C= X + Y = d x 2s
d
Example for floating-point adder
Exponents
a
Mantissas
b
R
Segment 1:
A
Difference=3-2=1
For example:
X=0.9504*103
Y=0.8200*102
Align mantissas
Choose exponent 3
R
Adjust
exponent
R
0.082
R
Add
mantissas
Segment 3:
Segment 4:
R
Compare
exponents
by subtraction
R
Segment 2:
B
S=0.9504+0.082=1.0324
R
4
Normalize
result
R
0.10324
Classification of Pipeline Processors
• There are various classification schemes for
classifying pipeline processors.
• Two important schemes are
1. Handler’s Classification
2. Li and Ramamurthy's Classification
Handler’s Classification
• Based on the level of processing, the pipelined
processors can be classified as:
1. Arithmetic Pipelining
2. Instruction Pipelining
3. Processor Pipelining
Arithmetic Pipelining
• The arithmetic logic units of a computer can
be segmented for pipelined operations in
various data formats.
• Example : Star 100
Arithmetic Pipelining
Arithmetic Pipelining
• Example : Star 100
– It has two pipelines where arithmetic operations
are performed
– First: Floating Point Adder and Multiplier
– Second : Multifunctional
• All scalar instructions
• Floating point adder, multiplier and divider.
– Both pipelines are 64-bit and can be split into four
32-bit at the cost of precision
Star 100 Architecture
Instruction Pipelining
• The execution of a stream of instructions can
be pipelined by overlapping the execution of
current instruction with the fetch, decode
and operand fetch of the subsequent
instructions
• It is also called instruction look-ahead
Instruction Pipelining
Example : 8086
• The organization of 8086 into a separate BIU
and EU allows the fetch and execute cycle to
overlap. This is called pipelining.
Processor Pipelining
• This refers to the processing of same data
stream by a cascade of processors each of
which processes a specific task
• The data stream passes the first processor
with results stored in a memory block which
is also accessible by the second processor
• The second processor then passes the refined
results to the third and so on.
Processor Pipelining
Li and Ramamurthy's Classification
• According to pipeline configurations and
control strategies, Li and Ramamurthy classify
pipelines under three schemes
– Unifunction v/s Multi-function Pipelines
– Static v/s Dynamic Pipelines
– Scalar v/s Vector Pipelines
Uni-function v/s Multi-function
Pipelines
Unifunctional Pipelines
• A pipeline unit with fixed and dedicated
function is called unifunctional.
• Example: CRAY1 (Supercomputer - 1976)
• It has 12 unifunctional pipelines described in
four groups:
– Address Functional Units:
• Address Add Unit
• Address Multiply Unit
Unifunctional Pipelines
– Scalar Functional Units
•
•
•
•
Scalar Add Unit
Scalar Shift Unit
Scalar Logical Unit
Population/Leading Zero Count Unit
– Vector Functional Units
• Vector Add Unit
• Vector Shift Unit
• Vector Logical Unit
Unifunctional Pipelines
– Floating Point Functional Units
• Floating Point Add Unit
• Floating Point Multiply Unit
• Reciprocal Approximation Unit
Cray 1 : Architecture
Cray -1
Multifunctional
• A multifunction pipe may perform different
functions either at different times or same
time, by interconnecting different subset of
stages in pipeline.
• Example 4X-TI-ASC (Supercomputer - 1973)
4X-TI ASC
• It has four multifunction pipeline processors,
each of which is reconfigurable for a variety of
arithmetic or logic operations at different
times.
• It is a four central processor comprised of nine
units.
Multifunctional
• It has
– one instruction processing unit
– four memory buffer units and
– four arithmetic units.
• Thus it provides four parallel execution
pipelines below the IPU.
• Any mixture of scalar and vector instructions
can be executed simultaneously in four pipes.
Architecture Overview of 4X-TI ASC
Static Vs Dynamic Pipeline
Static Pipeline
• It may assume only one functional
configuration at a time
• It can be either unifunctional or
multifunctional
• Static pipelines are preferred when
instructions of same type are to be executed
continuously
• A unifunction pipe must be static.
Dynamic pipeline
• It permits several functional configurations to
exist simultaneously
• A dynamic pipeline must be multi-functional
• The dynamic configuration requires more
elaborate control and sequencing mechanisms
than static pipelining
Scalar Vs Vector Pipeline
Scalar Pipeline
• It processes a sequence of scalar operands
under the control of a DO loop
• Instructions in a small DO loop are often
prefetched into the instruction buffer.
• The required scalar operands are moved into
a data cache to continuously supply the
pipeline with operands
• Example: IBM System/360 Model 91
IBM System/360 Model 91
• In this computer, buffering plays a major role.
• Instruction fetch buffering:
– provide the capacity to hold program loops of
meaningful size.
– Upon encountering a loop which fits, the buffer locks
onto the loop and subsequent branching requires less
time.
• Operand fetch buffering:
– provide a queue into which storage can dump
operands and execution units can fetch operands.
– This improves operand fetching for storage-toregister and storage-to-storage instruction types.
Architecture overview of IBM
360/Model 91
Vector Pipelines
• They are specially designed to handle vector
instructions over vector operands.
• Computers having vector instructions are called
vector processors.
• The design of a vector pipeline is expanded from
that of a scalar pipeline.
• The handling of vector operands in vector pipelines is
under firmware and hardware control.
• Example : Cray 1
Linear pipeline (Static & Unifunctional)
• In a linear pipeline data flows from one stage
to another and all stages are used once in a
computation and it is for one functional
evaluation.
Non-linear pipeline
• In floating point adder, stage (2) and (4)
needs a shift register.
• We can use the same shift register and then
there will be only 3 stages.
• Then we should have a feedback from third
stage to second stage.
• Further the same pipeline can be used to
perform fixed point addition.
• A pipeline with feed-forward and/or feedback
connections is called non-linear