Transcript new-unbehagen-802-1AB-rev-auto-attach

IEEE 802.1ABrev Extension for
Auto Attach
Nigel Bragg
Dan Romascanu
Paul Unbehagen
Scope
• Define a method of using IEEE 802.1AB Link Layer
Discovery Protocol (LLDP) with IEEE 802.1aq
Shortest Path Bridging (SPB) network to
automatically attach network devices not
supporting IEEE 802.1ah to individual services in
a SPB network.
– These network devices typically do not support SPBM,
MAC- in-MAC (802.1ah), nor I-SID usage and therefore
cannot easily take advantage of the SPB infrastructure
without manual configuration of attachment of VLANs
to I-SIDs in multiple locations
• Develop the extra MIB objects to the LLDP MIB as
needed
Conceptual SPB Auto Attach Model
SPB Network
Client
BEB Server
SPBM
LLDP
ISID
VLAN
LLDP Extensions
Type: 127 (7 bits)
Type: 127 (7 bits)
Length: 16 octets (9 bits)
Length: 41-506 octets
OUI: 3 octets
OUI: 3 octets
Subtype: 9 (1 octet)
Subtype: 8 (1 octet)
HMAC-SHA256 Digest: 32 octets
Element Type: 4 bits
Assignment Status: 4 bits
Mgmt VLAN: 12 bits
VLAN: 12 bits
System ID: 10 octets
I-SID: 3 octets
AA Element TLV
Service Assignment TLV
Applications
• Uses for Auto Attach (AA) have been identified
for numerous cases where end devices need to
signal the need to associate itself with specific
virtual networks identified by an ISID
• A prototype functional model was created using
Open vSwitch (OVS)
– Using a Standard 1U switch, OVS with LLDP TLV
extensions, and a state machine to manage the
communication of tlv’s.
– Creation and movement of VM’s triggered the
creation of AA LLDP TLV’s to the ToR’s from one server
to another.
Options
• Do nothing in IEEE 802.1
– may follow draft-unbehagen-lldp-spb as
Informational RFC
• As part of IEEE 802.1AB-REV
• New (small) project to amend IEEE 802.1AB
– … in which case the coming slides apply
Project process requirements
• Coexistence
– A WG proposing a wireless project shall
demonstrate coexistence through the preparation
of a Coexistence Assurance (CA) document unless
it is not applicable.
a) Will the WG create a CA document as part of the WG
balloting process as described in Clause 13? (yes/no)
b) If not, explain why the CA document is not applicable.
• Not applicable – this is not a wireless project.
5C requirements
• Broad market potential
– Each proposed IEEE 802 LMSC standard shall have
broad market potential. At a minimum, address the
following areas:
a) Broad sets of applicability.
b) Multiple vendors and numerous users.
a) The proposed revision would apply to all 802
networks that implement IEEE 802.1AB and IEEE
802.1aq
b) Some vendors and users have expressed their
support for this extensions and there are a
number of implementations successfully
deployed in the field.
5C requirements
• Compatibility
– Each proposed IEEE 802 LMSC standard should be in
conformance with IEEE Std 802, IEEE 802.1AC, and IEEE 802.1Q.
If any variances in conformance emerge, they shall be
thoroughly disclosed and reviewed with IEEE 802.1 WG prior to
submitting a PAR to the Sponsor.
a)
b)
–
Will the proposed standard comply with IEEE Std 802, IEEE Std
802.1AC and IEEE Std 802.1Q?
If the answer to a) is no, supply the response from the IEEE 802.1
WG.
The review and response is not required if the proposed
standard is an amendment or revision to an existing standard
for which it has been previously determined that compliance
with the above IEEE 802 standards is not possible. In this case,
the CSD statement shall state that this is the case.
a) Yes.
5C requirements
• Distinct Identity
– Each proposed IEEE 802 LMSC standard shall
provide evidence of a distinct identity. Identify
standards and standards projects with similar
scopes and for each one describe why the
proposed project is substantially different.
• There is no other 802 standard or approved
project that provides the same functionality
for bridges or end stations.
5C requirements
• Technical Feasibility
– Each proposed IEEE 802 LMSC standard shall provide
evidence that the project is technically feasible within the
time frame of the project. At a minimum, address the
following items to demonstrate technical feasibility:
a) Demonstrated system feasibility.
b) Proven similar technology via testing, modeling, simulation, etc.
a) There are numerous implementations of the IEEE
802.1AB and IEEE 802.1aq standards. This proposal
represents an extension of the first
b) The technology has been proven in the field and in
compatibility testing carried out in testing labs.
5C requirements
•
Economic Feasibility
– Each proposed IEEE 802 LMSC standard shall provide evidence of economic feasibility.
Demonstrate, as far as can reasonably be estimated, the economic feasibility of the proposed
project for its intended applications. Among the areas that may be addressed in the cost for
performance analysis are the following:
a)
b)
c)
d)
e)
a)
b)
c)
d)
e)
Balanced costs (infrastructure versus attached stations).
Known cost factors.
Consideration of installation costs.
Consideration of operational costs (e.g., energy consumption).
Other areas, as appropriate.
The functionality needed to provide the features specified in this standard is
essentially the same in bridges and end stations. The cost of providing these
features in each type of device will not be significant, given the expected large
volumes.
The cost factors are well known from implementations of IEEE 802.1AB. We are
basically talking about a software upgrade
There are no incremental installation costs relative to the existing costs
associated with IEEE 802.1AB and IEEE 802.1aq
There are no incremental operational costs relative to the existing costs
associated with IEEE 802.1AB and IEEE 802.1aq
No other areas have been identified.