Transcript Orthographic Projection - Ivy Tech -

Orthographic Projection
Chapter 4
Objectives
•
•
•
Recognize and sketch the symbol for
third-angle projection
List the six principal views of projection
Sketch the top, front and right-side
views of an object with normal,
inclined, and oblique surfaces
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
2
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Objectives (cont.)
•
•
•
Understand which views show depth in
a drawing that shows top, front, and
right-side views
Now the meaning of normal, inclined,
and oblique surfaces
Compare and contrast using a CAD
program to sketching on a sheet of
paper to create 2-D drawing geometry
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
3
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Objectives (cont.)
•
•
•
Know which dimensions transfer
between top, front, and right-side views
Transfer the depth between the top and
right-side views
Label points where surfaces intersect
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
4
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Views of Objects
•
•
•
Drawings are two-dimensional
representations of objects that allow you to
record sizes and shapes precisely
To provide a complete and clear description,
the views must be systematically arranged
The system of views is called multiview
projection
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
5
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
The Six Standard Views
•
Any object can
be viewed from
six mutually
perpendicular
views
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
6
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
The Six Standard Views
•
These views are called principal views
and are arranged in a standard way
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
7
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
The Six Standard Views
•
•
•
The top, front, and bottom views align
vertically
The rear, left-side, front, and right-side
views align horizontally
To draw a view out of place is a serious
error
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
8
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Principal Dimensions
•
The three principal
dimensions of an
object are:
•
•
•
Width
Height
Depth
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
9
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Principal Dimensions
•
•
•
•
Any principal view shows two of the
three principal dimensions
Height is shown in the rear, left-side,
front, and right side
Width is shown in the rear, top, front,
and bottom
Depth is shown in the left-side, top,
right-side, and bottom views
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
10
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Projection Method
•
•
•
Frontal plane – the plane upon which
the frontal view is projected
Horizontal plane – the plane upon
which the top view is projected
Profile plane – the plane upon which
the side view is projected
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
11
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
The Glass Box
•
•
One way to understand the standard
arrangement of views on a sheet of
paper is to envision the object in a glass
box
The outside observer would see six
standard views of the object through
the sides of this imaginary glass box
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
12
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
The Glass Box
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
13
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Transferring Depth Dimensions
•
The depth dimensions in the top and
side views must correspond
•
You may find it convenient to use dividers,
a scale, or a 45-degree miter line to project
dimensions
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
14
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Necessary Views
•
A sketch or drawing should only contain
the views needed to clearly and
completely describe the object
•
•
•
Choose the views that have the fewest
hidden lines and show essential contours
or shapes most clearly
Complicated objects may require more
than three views
Some objects only need one or two views
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
15
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Necessary Views
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
16
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Necessary Views
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
17
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Necessary Views
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
18
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Orientation of the Front View
•
The front view should:
•
•
•
Show a large surface of the part parallel to
the front viewing plane
Show the shape of the object clearly
Show the object in a usual, stable, or
operating positions
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
19
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Orientation of the Front View
•
•
When possible, a machine part is drawn
in the orientation it occupies in the
assembly
Usually screws, bolts, shafts, tubes, and
other elongated parts are drawn in a
horizontal position
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
20
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Orientation of the Front View
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
21
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
First- and Third-Angle Projection
•
There are two main systems used for
projecting and unfolding the views:
•
•
•
Third-angle projection which is used in the
United States, Canada and some other
countries
First-angle projection which is primarily
used in Europe and Asia
You should understand both methods
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
22
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Third-angle Projection
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
23
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
First-angle Projection
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
24
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Hidden Lines
•
An advantage of orthographic views is
that each view shows the object all the
way through as if it were transparent
•
•
•
Thick dark lines represent visible features
Dashed lines represent features that would
be hidden behind other surfaces
When possible, choose views that show
features with visible lines
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
25
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
26
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Centerlines
•
The centerline is used to:
•
•
•
•
Show the axis of symmetry of a feature or
part
Indicate a path of motion
Show the location for bolt circles or other
circular patterns
The centerline pattern is composed of
three dashes, one long dash on each
end with a short dash in the middle
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
27
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Centerlines
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
28
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Precedence of Lines
•
When lines coincide on a drawing the
rules of precedence are:
•
•
Visible lines always take precedence over
hidden or centerlines
Hidden lines take precedence over
centerlines
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
29
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Precedence of Lines
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
30
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Visualization
•
•
Even those with experience can’t always
look at a multiview sketch and instantly
visualize the object represented
You will learn to interpret lines in a
logical way in order to visualize the
object as a whole
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
31
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Views of Surfaces
•
•
•
A plane surface that is perpendicular to
a plane of projection appears on edge
as a straight line
If a plane is parallel to the plane of
projection, it appears true size
If a plane is angled to the plane of
projection, it appears foreshortened
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
32
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Views of Surfaces
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
33
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Views of Surfaces
•
A plane surface always projects either
on edge or as a surface in any view
•
It can appear foreshortened, smaller than
actual size, but it can never appear larger
than its true size in any view
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
34
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Normal Surfaces
•
A normal surface
is parallel to a
plane of
projection
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
35
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Inclined Surfaces
•
An inclined
surface is
perpendicular to
one plane of
projection but
inclined to
adjacent planes
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
36
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Oblique Surfaces
•
An oblique surface
is tipped to all
principal planes of
projection and does
not appear true size
in any standard
view
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
37
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Edges
•
•
The intersection of two plane surfaces
of an object produces an edge which
shows as a straight line in a drawing
If an edge is perpendicular to a plane of
projection it appears as a point,
otherwise it appears as a line
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
38
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Parallel Edges
•
When edges are parallel to one another
on an object, they will appear as
parallel lines in every view unless they
align one behind the other
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
39
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Angles
•
•
If an angle is in a normal plane, it will
show true size on the plane of
projection to which it is parallel
If an angle is in an inclined plane, it
may be projected either larger or
smaller than the true angle depending
on its position
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
40
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Angles
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
41
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Interpreting Lines
•
A straight, visible, or hidden line in a
sketch has three possible meanings:
•
•
•
•
An edge between two surfaces
The edge view of a surface
The limiting element of a curved surface
Since no shading is used on
orthographic views, you must examine
all views to determine a line’s meaning
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
42
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Interpreting Lines
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
43
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Similar Shapes of Surfaces
•
If a flat surface is viewed from several
different positions, each view will show
the same number of sides and vertices
and same characteristic shape
whenever it appears as a surface
•
This consistency of shapes is useful in
analyzing views
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
44
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Similar Shapes of Surfaces
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
45
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.
Interpreting Views
•
•
One method of interpreting sketches is
to reverse the mental process used in
projecting them
Each view provides certain definite
information about the shape of the
object and all are necessary to visualize
it completely
Technical Drawing 13th Edition
Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart
46
© 2009 Pearson Education, Upper Saddle River, NJ 07458.
All Rights Reserved.