Transcript h/t
N.W.F.P. University of Engineering and
Technology Peshawar
Lecture 13: Plate Girder
By: Prof Dr. Akhtar Naeem Khan
[email protected]
1
Plate Girders
A girder is a flexural member which is required
to carry heavy loads on relatively long spans
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
2
Plate Girder
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
3
Plate Girder
Plate girders are typically used as long-span
floor girders in buildings, as bridge girders, and
as crane girders in industrial structures.
Commonly term girder refers to a flexural xsection made up of a number of elements.
They are generally considerably deeper than the
deepest rolled sections and usually have webs
thinner than rolled sections.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
4
Plate Girder
Modern plate girders are normally fabricated
by welding together two flanges and a web
plate.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
5
Plate Girder
Plate girders are at their most impressive in
modern bridge construction where main spans of
well over 200m are feasible, with corresponding
cross-section depths, haunched over the
supports, in the range of 5-10m.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
6
Plate Girder
Because plate girders are fabricated
separately, each may be designed
individually to resist the applied
actions using proportions that ensure
low self-weight and high load
resistance.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
7
Plate Girder
Changes in X-Section
There is also considerable scope for variation
of cross-section in the longitudinal direction.
A designer may choose to reduce the flange
thickness (or breadth) in a zone of low
applied moment.
Equally, in a zone of high shear, the designer
might choose to thicken the web plate.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
8
Plate Girder
Changes in Material
Alternatively, higher grade steel might be
employed for zones of high applied moment
and shear, while standard grade would be
used elsewhere. So-called "hybrid" girders
with different strength material in the flanges
and the web offer another possible means of
more closely matching resistance to
requirements.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
9
Plate Girder
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
10
Plate Girder
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
11
Plate Girder
Any cross-section of a plate girder is normally
subjected to a combination of shear force and
bending moment.
The primary function of the top and bottom
flange plates of the girder is to resist the axial
compressive and tensile forces arising from
the applied bending moment.
The primary function of the web plate is to
resist the applied shear force.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
12
Plate Girder
Plate girders are normally designed to support
heavy loads over long spans in situations where it
is necessary to produce an efficient design by
providing girders of high strength to weight ratio.
To produce the lowest axial flange force for a
given bending moment, the web depth (d) must be
made as large as possible. To reduce the self
weight, the web thickness (tw) must be reduced to
a minimum.
As a consequence, in many instances the web
plate is of slender proportions and is therefore
prone to buckling at relatively low values of
applied shear.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
13
Plate Girder
For efficient design it is usual to choose a
relatively deep girder, thus minimizing the
required area of flanges for a given applied
moment, Msd.
This obviously entails a deep web whose
area will be minimized by reducing its
thickness to the minimum required to carry
the applied shear, Vsd.
Such a web may be quite slender (i.e. a high
d/tw ratio) and may be prone to local buckling
and shear buckling.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
14
Plate Girder
Web buckling does not determine the
ultimate strength of a plate girder.
Plate elements do not collapse when they
buckle; they can possess a substantial postbuckling reserve of resistance.
For an efficient design, any calculation
relating to the ultimate limit state should take
the post-buckling action into account.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
15
Design Criteria
Criteria for design of plate girder may be
based on
Elastic bend-buckling strength
Elastic shear-buckling strength
Post-bend-buckling strength
Post-shear-buckling(Tension field)strength
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
16
Design Criteria
The designer has the choice of following four
combinations
1. Elastic bend buckling + Elastic shear buckling
(conventional flexural behavior)
2. Elastic bend buckling + Post shear buckling
3. Post bend buckling + Elastic shear buckling
4. Post bend buckling + Post shear buckling
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
17
Elastic Bend Buckling
Strength
The extreme fiber bending stress at which a
perfectly flat web buckles is given by
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
18
Elastic Bend Buckling
Strength
Using a FOS of 1.25 w.r.t service load bending
stress fb gives an eqnuation which is AASHTO
slenderness limit for plat girders webs
Using AASHTO allowable stress fb=0.55Fy
“ h/t=165 for A36 steel “
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
19
Elastic Bend Buckling
Strength
The bend buckling resistance of beam webs can be
increased considerably by reinforcing the slender webs
with Longitudinal stiffeners.
Means webs thinner than those given by the equation can be
used.
A typical longitudinally stiffened girder is shown after failure
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
20
Web Stiffeners
They usually consists of rectangular
bars to welded to web.
Transverse stiffeners may be in pairs,
one on each side of web, or they may
placed on one side of web.
Longitudinal stiffeners are usually
placed on one side of web.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
21
Web Stiffeners
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
22
Web Stiffeners
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
23
Web Stiffeners
The main function of the longitudinal stiffeners is
to increase the buckling resistance of the web
with respect of both shear and bending loads. An
effective stiffener will remain straight, thereby
sub-dividing the web panel and limiting the
buckling to the smaller sub-panels. The resulting
increase in the ultimate resistance of the girder
can be significant.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
24
Web Stiffeners
Efficiency of stiffener is a function of its location
in the compression zone
The optimum location for a longitudinal stiffener
has been determined to be at least h/5 from
compression edge.
In this case k=129. The corresponding allowable web
slenderness is h/t=330 as compare to 165
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
25
Web Stiffeners
Stiffener acts as a beam supported at the ends
where a vertical stiffener holds the web in line.
Stiffener acts as a beam column and hence must
be proportioned in terms of x-sectional area and
moment of inertia.
AASHTO specifies Is as
Stiffener acts as a beam supported at the ends
where a vertical stiffener holds the web in line.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
26
Web Stiffeners
The stiffeners must also be proportioned to
resist local buckling.
For plates supported on one longitudinal
edge AASHTO require b/t<1625/fb
Multiple longitudinal stiffeners are used for
large depth webs.
As longitudinal stiffener is also acting as a
column so it must be satisfied for critical
stress (Fcrs>0.6Fcrf)
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
27
Post buckling bending
strength
If bending strain increases after Fcr, the upper
edge of panels shortens and bottom edge
lengthens.
If web were to remain flat there will be increase in
stress.
Because the web has buckled, the increase in
stress is non-linear.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
28
Post buckling bending
strength
As variation in post-buckled state is not known,
simplify assumptions are made.
Non-linear compression is replaced with linear
distribution acting on effective depth be.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
29
Post buckling bending
strength
Point A gives point that enables a girder to reach its full
yield moment(925 /Fy=154).
If stiffeners at h/5 is provided gives point B.
Considering the
post buckling
strength, the
point where
reduction in web
effectiveness
begins s taken to
be 980/Fy=170.
CE-409: Lecture 13
B
A
0.94
0.82
M/My
0.4
0.18
154
315
360
h/t
Prof. Dr Akhtar Naeem Khan
30
Post buckling bending
strength
Equation connecting the revised point A
with points corresponding to h/t=360 is
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
31
Post buckling bending
strength
LRFD
Where
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
32
Compression Flange Vertical
buckling
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
33
Compression Flange Vertical
buckling
If plate-girder web is too slender, the compression
flange may buckle in vertical plane at stress less
than yield stress.
The compression flange is a beam-column
continuous over vertical stiffener as supports
Its stability depends on stiffener spacing and
relative stiffness of the flange and the web. Fcr is
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
34
Compression Flange Vertical
buckling
Slenderness of webs with vertical stiffeners is taken conservatively
AISC ASD/LRFD limits the h/t by the given equation with
Aw/Af =0.5
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
35
Shear buckling of beam webs
Shear buckling is seldom a determining
factor in design of rolled section but
plate girders have much larger h/t so it
must be considered.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
36
Shear buckling of beam webs
Transverse stiffeners are used to
increase the buckling strength by
increasing factor k through a reduction
in aspect ratio a/h.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
37
Transverse Stiffeners
Transverse stiffeners play an important role in
allowing the full ultimate load resistance of a
plate girder to be achieved.
In the first place they increase the buckling
resistance of the web;
Secondly they must continue to remain effective
after the web buckles, to provide anchorage for
the tension field;
finally they must prevent any tendency for the
flanges to move towards one another.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
38
Transverse Stiffeners
The satisfactory performance of a
transverse stiffener can best be illustrated
by comparing the girders shown, after
testing.
Figure 2
Figure 1
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
39
Transverse Stiffeners
In Figure 1 the stiffeners have remained straight.
In Figure 2 the stiffener has failed and has been
unable to limit the buckling to the adjacent subpanels of the girder; instead, the buckle has run
through the stiffener position extending over
both panels. Consequently, significant reduction
in the failure load of the girder occurred.
In Figure 1 One can also see the effect of aspect
ratio,i.e greater a/h less k and small Fcr.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
40
Transverse Stiffeners
The stiffener must be of adequate
rigidity in the direction perpendicular to
the plane of the web to prevent web
buckling. This condition is satisfied
provided the stiffener has a second
moment of area Is that satisfies the
following empirical formulae:
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
41
Transverse Stiffeners
AISC/LRFD Moment of Inertia of
stiffener is:
where
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
42
Transverse Stiffeners
Transverse stiffeners spacing can be
determined from the following
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
43
Tension Field Action
The resulting shear stresses on an
element of a web are equivalent to
principal stresses, one Tensile and one
Compressive, at 45 to the shear stress.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
44
Tension Field Action
Once a web panel has buckled in shear, it
loses its resistance to carry additional
compressive stresses.
On the other hand tensile principal stress
continues to increase in strain in the
diagonal direction.
Such a panel has a considerable post buckling strength,
since increase in tension is limited only by yield stress.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
45
Tension Field Action
In this post-buckling range, a new load-carrying
mechanism is developed, whereby any additional
shear load is carried by an inclined tensile
membrane stress field. This tension field anchors
against the top and bottom flanges and against the
transverse stiffeners on either side of the web
panel. The load-carrying action of the plate girder
than becomes similar to that of the N-truss
In the post-buckling range, the resistance offered by
the web plates is analogous to that of the diagonal
tie bars in the truss.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
46
Tension Field Action
Phases of behavior up to collapse of a typical panel in shear
Prior to Buckling
CE-409: Lecture 13
Post Buckling
Prof. Dr Akhtar Naeem Khan
Collapse
47
Tension Field Action
The load-carrying action of the plate girder
than becomes similar to that of the N-truss
In the post-buckling range, the resistance
offered by the web plates is analogous to
that of the diagonal tie bars in the truss.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
48
Tension Field Action
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
49
Tension Field Action
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
50
Tension Field Action
V
ft
V
Vt=Tsin
Vt = ft ht cos sin
T=ft ht cos
Vt = (1/2)ft ht sin2
Vt =(1/2) ft ht
=45
Vty=(1/2) Fy ht………….(1)
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
51
Tension Field Action
Vty
=(1/2) Fy ht
Vy
Fvy ht
= Fy
2Fvy
Vty = 3 Vy = 0.87 Vy
2
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
52
Tension Field Action
The angle for which Vt is max
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
53
Tension Field Action
Where
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
54
Tension Field Action
(1)
Taking inelastic and strain hardening range
(2)
(3)
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
55
Tension Field Action
Codal equations are derived from
eqn;(1),(2),(3)
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
56
Tension Field Action
AISC/LRFD
k
a/h
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
57
Combined Bending & Shear
of Webs
Interaction diagram is based on Tensionfield of webs
If the web is completely yielded in
shear,any accompanying moment must
be resisted entirely by flanges.
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
58
Combined Bending & Shear
Bending & shear Interaction Curve
B
B C
V/(FvyAw)
E 1/3
0.75 0.83
CE-409: Lecture 13
D
1.0 1.07 1.12
Prof. Dr Akhtar Naeem Khan
M/My
59
Combined Bending & Shear
1.0
Mu/Mn
0.8
0.6
LRFD Interaction Curve
0.4
0.2
0.2
CE-409: Lecture 13
0.4
0.6
0.8
Prof. Dr Akhtar Naeem Khan
1.0
Vu/Vn
60
Web Proportioning
Notations
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
61
Web Proportioning
Depth of girder is influenced by many
factors:
Headroom
Clearance for high water in deck bridges
Traffic passing beneath the bridge
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
62
Web Proportioning
Depth: Overall girder depth, h, will
usually be in the range
Lo/12 h Lo/8,
occasionally lighter loads may be
accommodated with Lo/20.
Flange:
The breadth, b, will usually be in the range
h/5 b h/3,
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
63
Design Procedure
1. Maximum Moment & Shear for Factored Load
2. Web Design
1.
Assume depth of girder L/12 h L/8
2.
Depth of Web hw=h-2tf
3.
Web slenderness
1.
For a/h <5 …………….
2.
and for a/h > 5 ……………………
3.
hw/tw= 970/Fy
4.
Select optimum tw
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
64
Design Procedure
4. Flange Design
1.
Find Af
2.
Select suitable tf and bf
3.
Flange slenderness
1.
CE-409: Lecture 13
bf/ 2tf < 65/Fy …………….Compact
Prof. Dr Akhtar Naeem Khan
65
Design Procedure
5. Check trial girder section
1.
Web local buckling limit state
1.
2.
2.
640/Fy< hw/tw < 970/Fy……Non-Compact
3.
hw/tw > 970/Fy…………………..Slender
Flange local buckling limit state
1.
3.
hw/tw< 640/Fy…………………..Compact
bf/ 2tf < 65/Fy …………….Compact
Lateral Torsional Buckling
1.
Calculate Iy
2.
A=Af+Aw/6
3.
ry= Iy/A
4.
Find Lb/ry
5.
p= 300/Fy ………….. < p ______Compact
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
66
Design Procedure
6. Bending strength
1.
Calculate Ix
2.
Calculate Sxt
3.
.
4.
.
5.
Mn Mu
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan
67
Procedure for Design
6. Bending strength
1.
Calculate Ix
2.
Calculate Sxt
3.
.
4.
.
5.
Mn Mu
CE-409: Lecture 13
Prof. Dr Akhtar Naeem Khan