Transcript QC tools

Quality control tools
www.mbaknol.com
Introduction
• Seven QC tools are fundamental instruments to improve the
quality of the product. They are used to analyze the production
process, identify the major problems, control fluctuations of
product quality, and provide solutions to avoid future defects.
Statistical literacy is necessary to effectively use the seven QC
tools. These tools use statistical techniques and knowledge to
accumulate data and analyze them.
• Seven QC tools are utilized to organize the collected data in a
way that is easy to understand and analyze. Moreover, from
using the seven QC tools, any specific problems in a process
are identified.
www.mbaknol.com
7QC tools always include :
•
•
•
•
•
•
•
Check Sheet
Pareto Chart
Cause-and-Effect Diagram
Histogram
Scatter Diagram
Flow Chart
Control Chart
www.mbaknol.com
Check Sheet
• A check sheet is a pre-designed format for collection of data
that encourages organized collection and groups data into
categories.
• When to use it: To keep track of the parameters of an on
going process. It can be used to track events by such factors as
timeliness, reason for inspection failure, etc
• How to use it: Look at some preliminary data before
developing the check sheet. This will indicate what categories
to use.
www.mbaknol.com
• Used for the collection of quantitative or qualitative repetitive
data. Adaptable to different data gathering situations.
Minimal interpretation of results required. Easy and quick to
use.
www.mbaknol.com
Pareto Chart
• A simple rule, pareto, 20 % issues causes 80 % results. This means, 80 % if
problems come from 20 of reasons. 80 % of results come from 20% of
work. 80% of cost come from 20% of spent area...and so on.
• When to Use
Use it when there are many problems or opportunities and you want to
focus on the most important. Or when your analyzing data about the
frequency of problems or causes in a process.
www.mbaknol.com
Constructing a Pareto chart:
1.Decide the categories to compare.
2.Determine the appropriate measurement.
3.Decide the period of time for the chart.
4.In a table, collect the data for each category.
5.Arrange the categories in descending way per the total sums.
6.Construct and label bars for each category.
7.Calculate the percentage for each category.
8.Calculate and draw cumulative percentage.
•
Analysis of the Pareto Chart
www.mbaknol.com
Cause-and-Effect Diagram (Fishbone Diagram)
• The Cause and Effect diagram identifies many possible causes
for an effect or a problem.
• When to Use
When your figuring out the possible factors for a problem.
When your team’s thinking hits a roadblock.
www.mbaknol.com
Procedure
• 1- Agree on the problem (effect).
• 2- Brainstorm the possible major categories of causes of the problem (5M
and 1E).
• 3- Write the categories of causes as branches from the main arrow.
• 4- Brainstorm all the possible factors for each of the major categories.
• 5- Again ask “why does this happen?” about each branch from step 4.
• 6 After completion, have the team review the diagram
www.mbaknol.com
Example:
www.mbaknol.com
Histogram
•
shows a bar chart of accumulated data and provides the easiest way to
evaluate the distribution of data.
• This chart graphs data distributions. If you have numerical, variable,
continuous data you can use the this chart. The chart organizes and sorts
the data. It shows the data in a pictorial format.
www.mbaknol.com
Construction
•
Collect at least 50 data points from a process.
•
Use the worksheet to set up the chart.
•
After calculating width in step 2 of the worksheet, use your judgment and
adjust it to a convenient round number.
•
Draw x- and y-axes on graph paper. Mark and label the y-axis for counting the
data values. Mark and label the x-axis with the L values from the worksheet.
•
For each data point, locate it where it fits within the Ls. Mark off one count
above the appropriate bar with an X or by shading that portion of the bar.
www.mbaknol.com
•
Scatter Diagram
is a graphical tool that plots many data points and shows a pattern of
correlation between two variables.
• Scatter Diagram Is used to investigate the possible relationship between
two variables that both relate to the same "event".
When to Use:
• When you have paired numerical data.
• When trying to identify potential root causes of problems.
• After brainstorming causes and effects using a fishbone diagram, to
determine objectively whether a particular cause and effect are related.
• When determining whether two effects that appear to be related both
occur with the same cause.
www.mbaknol.com
Procedure
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1. Collect pairs of data where a relationship is suspected.
2. Draw a graph with the independent variable on the horizontal axis and the
dependent variable on the vertical axis.
3. Look at the pattern of points to see if a relationship is obvious.
4. Divide points on the graph into four quadrants. If there are X points on the
graph.
5. Count X/2 points from top to bottom and draw a horizontal line.
6. Count X/2 points from left to right and draw a vertical line.
7. If number of points is odd, draw the line through the middle point.
8. Count the points in each quadrant.
9. Add the diagonally opposite quadrants.
10. A = points in upper left + points in lower right
11. B = points in upper right + points in lower left
12. Q = the smaller of A and B
13. N = A + B
14. Look up the limit for N on the trend test table.
15. If Q is less than the limit, the two variables are related.
16. If Q is greater than or equal to the limit, the pattern could have occurred from
random chance.
www.mbaknol.com
Example
www.mbaknol.com
Flow Chart
•
shows the process step by step and can sometimes identify an
unnecessary procedure.
When to Use:
• One of the first activities of a process improvement effort is
constructing a flowchart. It provides the following benefits:
1- It give you and everyone a clear understanding of the process.
2- Facilitates teamwork and communication.
3- Helps to identify non-value-added operations.
www.mbaknol.com
Method:
•
•
There are many symbols used to construct a flowchart; the more common
symbols are shown below:
Identify the process steps and link them together with direction arrows
www.mbaknol.com
Control Chart
•
provides control limits which are generally three standard
deviations above and below average, whether or not our
process is in control.
• Control charts are graphs used to study how a process changes
over time.
• Data is plotted in time order. A control chart always has a
central line for the average, an upper line for the upper control
limit and a lower line for the lower control limit. These three
lines are determined from historical data.
www.mbaknol.com
When to Use:
•
• When controlling ongoing processes by finding and correcting problems as
they occur.
•
• When predicting the expected range of outcomes from a process.
•
• When determining whether a process is stable (in statistical control).
•
• When analyzing patterns of process variation from special causes (nonroutine events) or common causes (built into the process).
•
• When determining whether your quality improvement project should aim to
prevent specific problems or to make fundamental changes to the process.
www.mbaknol.com
Basic Procedure
• 1. Choose the appropriate control chart for your data.
• 2. Determine the appropriate time period for collecting and plotting
data.
• 3. Collect data, construct your chart and analyze the data.
• 4. Look for “out-of-control signals” on the control chart. When one is
identified, mark it on the chart and investigate the cause. Document
how you investigated, the root cause and how it was corrected.
www.mbaknol.com
Example
www.mbaknol.com