Transcript RODRILL IMPACT MAST - FoundationEquipment.com

RODRILL IMPACT MAST
MODEL ROIM-45
RODRILL Impact Mast is made in America. Masts range from 40’ to 70’ in overall length depending on
your order. The mast consists of 4 main parts, the Mast structure, the Sled, the Boom Tip Connector,
Vibratory Hammer, Hopper and Mandrel.
The Impact Mast is typically installed on an excavator such as John Deere / Hitachi 450 / Caterpillar 345
or larger excavator. Application on smaller machines such as Cat 330 may be possible depending on
mast length and vibratory hammer selection.
The Impact vibro mast is sold with, and designed to operate with, proprietary vibratory hammers. These
hammers are manufactured by American Pile Driving Equipment (APE) located in Kent, WA. These APE
Vibratory Hammers are modified specifically for Geopier application. Available hammers range from 500
to 2500 inch pounds of Eccentric moment. The Vibro Hammer is fixed moment, variable amplitude,
however variable moment hammers are available on special order basis. We have found that with the
crowding ability of the Impact Mast, the fixed moment hammers perform well without the added
complexity of the variable moment option. Vibro Hammers are available with Dynamic force ranging from
40 to 150 tons.
IMPACT MAST WITH 45’ CAPACITY, 59’ (17m) OAL
Standard Mast:









Includes the Holmes/Peterson Hopper and Mandrel setup.
Is 40’ container able.
Includes 3 parts Hoist System with max pull of 18- 22 tonnes and 2 part crowd of 15 tonnes.
Pressure gauge at cab to read hydraulic pressure for correlation to crowd pressure (customer to
perform calibration in field).
In cab foot switch for set up functions.
Side tilt = 3 degrees.
Boom tip connector to fit your 450 class Excavator.
Wiring, vibro hosing, and fittings to attach the “Impact Mast” to your excavator.
Vibro sled + safety limit cables from vibro sled to hopper inc pad eyes
UPPER SHEAVES
GP 13.2 VIBRO
 60’ MAST / 48’ MANDREL TRAVEL
 45,000 LB HOIST / 30,000 LB CROWD CAPACITY
 FORE / AFT LEVELING
 SIDE/ SIDE LEVELING
 NO CHANGE TO EXCAVATOR HYD SYSTEM
 PRESSURE CONTROL & VALVES ON MAST
 LOCKING VALVES
 SELF ERECTING
AUTO LOADING
BUCKET
HOPPER
AUX. WINCH
MANDREL
CROWD & HOIST
WINCHES
BOOM TIP CONNECTOR
LOWER SHEAVE
REMOVABLE FOOT
DAILY INSPECTIONS
1. Inspect wire rope for kinks, broken wires or other damage.
2. Check shackles for proper fit and security.
3. Inspect all hoses for kinks, and fitting for leaks.
4. Inspect bolts for obvious signs of looseness, including, but not necessary limited to the following areas:
A. Mast connector bolts.
B. Winch & motor mounts.
5. Inspect pins and retainers for wear and looseness, including, but not necessarily limited to the
following areas:
A. Tilt Cylinders.
B. Boom Pivot Pin.
C. Stick Pin.
D. Tilt Pin.
E. Top and Bottom Sheaves.
F. Upper Sheave Pins and Thrust Washers.
G. Lower Sheave Pin and Thrust Washers.
6. Check slide poly material for proper operation and wear.
7. Refer to upper winch service manuals for winch maintenance.
8. Provide grease to lubrication points daily.
WEEKLY INSPECTIONS
1. Perform all daily inspections items.
2. Provide grease and lubrication at points required.
3. Perform maintenance per winch service manuals.
PRESSURE GAUGE PORTS
GREASE POINTS
CROWD/HOIST BRAKE ADJ.
AUX. WINCH
CROWD WINCH
HOIST WINCH
WINCH BRAKE ADJ. VALVES
VIBRO / STICK CYLINDER
SELECTOR
WINCH MANIFOLD
TILT CYLINDER / WINCH
SELECTOR
SELD MANIFOLD / VIBRO
CONNECTIONS
MANUAL WINCH BRAKE
RELEASES
VIBRO AND WINCH
FLOW CONTROL
(Consult Mfg. Prior to
Adjustment)
1.
2.
3.
4.
5.
The cost is lower than that offered by competitors.
Low cost transportation. All components can be loaded into standard 40’ shipping containers.
Mast can be torn down or assembled on site in 2-3 days.
Low maintenance.
Very few spare parts needed.








Upper sheaves, pins and washers.
Sled sheaves, pins and washers.
Crowd cable ¾’’ x 135 ft.
Hoist cable ¾’’ x 225 ft.
Auto dump bucket cable ½’’ x 175 ft.
Auto dump bucket sheave pulleys, pins and washers.
Spare crowd/hoist winch.
Spare self loader winch.
1
1
1
1
1
1
1
1
We thank you for your interest on our Impact Mast.
Frank Rodriguez [email protected]
Nathan Massey [email protected]
Randy Settlage [email protected]
RODRILL INC
11670 IH 10 East, Converse, TX 78109
Phone. (210) 667. 2130
Fax. (210) 667 . 9755
Web Page: www.rodrill.com
American Pile Driving Equipment (APE)
Kent, Washington
Phone. (206) 369 . 2999
Website. www.apevibro.com