Transcript Drum OD Band Fixed Anchor OD servo

BOLT SEQUENCE
.
Loosening – start with #25
Tightening – start with #1
Numbered bolts are 8mm,
others are 10mm
Guide Pin
Bolt 10mm
All bolts
torqued 90120 in/lbs
Guide Pin
Bolt 10mm
Outer line on MLPS
must line up with
inner line with
shifter in Neutral
MLPS
MLPS
attachment
bolts (2)
Shift linkage
shaft
Shift linkage
arm
Picture is 95 model
Manual Valve
Parking Pawl
Shaft tab fits
into manual
valve groove
Shift linkage
shaft
Rooster Comb
Spring
Picture is 95 model
Shift Tab
Manual Valve
Shaft tab fits
into manual
valve groove
EPC Solenoid
Picture is 95 model
Linkage Pin
Round Screen
TCC Solenoid
Shift Solenoid
Pack
EPC Solenoid
Reverse
Servo
1-2 Piston
2-3 Piston
Linkage
Pin
1-2 Piston
Round Screen
(earlier models)
Larger screen here
on later models
2-3 Piston
Access OD
Band here
OD
Servo
Reverse
Servo
Picture is 95 model
Round
check
valve
Check
Balls (8)
Square
Screen
Manual Valve
Debris can get
trapped inside
valve body
Reinforcement
Plates – note
orientation
Separator
Plate
Manual
Valve
Picture is 95 model
End plug with threaded
hole
Earlier models
only
Extra bolt
Note sequence of parts for each valve
Note sequence of parts for each valve
This one has 2
valves and 2
clips
Note sequence of parts for each valve
Must be spotless!
Shift linkage retaining nut is partially
visible here
“Rooster
comb”
Linkage
shaft
Parking pawl
Picture is 95 model
Shift
linkage
EPC
Solenoid
Picture is 95 model
2.7” OD
servo
OD band
Anchor bracket (ea
end)
OD Servo
Stock OD
servo
return
spring
OD servo
removal bracket
Valve Body
Bolts
Center bolt with nut tackwelded to other side of
bracket
Correct Band Position
OD Band
Fixed
Anchor
Drum
Contact
tighten
OD servo
loosen
Band out of Position
OD Band
Fixed
Anchor
Drum
No contact
tighten
OD servo
loosen
Maintaining Band Position
OD Band
Fixed
Anchor
Drum
Use screwdriver
or similar to
push/keep band
into proper
position while
servo is removed
push
Separator
plate top
gasket
Picture is 95 model
EPC
Solenoid
TCC
Solenoid
Shift
Solenoids
Filter
Wire
Harness
Valve
Body
Temp
Sensor
Picture is 95 model
Filter (note extension for
later model deeper pan)
Plastic
Harness
Manual
Valve
Picture is 02 model
Shift
Solenoids
TCC
Solenoid
Transmission filer
o-ring needs to be
removed
Shift linkage fits
into manual valve
Shift
Solenoids
Plastic
harness
TCC
Solenoid
Picture is 02 model
Valve body bolt retains
shift solenoid bracket
Shift
Solenoids
Picture is 02 model
Use small screwdriver to gently pry
out retaining tabs on harness
Plastic
harness
Picture is 02 model
Plastic
harness
Sonnax upgrade parts
Picture is 02 model
Pressure regulator
valve
Sonnax 76948-09
upgrade
Picture is 02 model
8mm valve body
bolt retains shift
solenoid bracket
Shift Solenoids
Valve body
cover plate
TCC
Solenoid
10mm bolt
retains both
brackets
Picture is 02 model
Manual valve
OD servo regulator
valve & sleeve
Sonnax 76948-29K
upgrade
Picture is 02 model
OD Servo
OD band can be seen
here – this is where flat
blade object can be
used to push against
band to retain it when
OD servo is removed
Picture is 02 model
OD servo
removal bracket
Flat blade bar
pushed against
OD band to
retain it while
OD servo is
removed
Picture is 02 model
OD servo
OD Servo
Stock (stiffer)
OD return
spring
Hi-perf (softer) OD
return spring
1-2 piston/accumulator
cover
Screen fits up
into case here
before valve
body is
installed
Picture is 02 model
Molded Rubber
OEM gasket
Deeper (later
model) pan
Magnet