MREA_2BPDR_9-1.0 - University of Michigan
Download
Report
Transcript MREA_2BPDR_9-1.0 - University of Michigan
Preliminary Design Review (PDR)
The University Of Michigan
2011
1
Vehicle: i.
2
Vehicle: ii.
Nose
Main Chute Separation Bay
Main Chute Separation
3
Vehicle: iii.
Main Chute Seperation
Aviation Bay
Aviation Bay Access Cut
Apogee Separation Bay
Apogee Separation
4
Vehicle: iv.
Apogee Separation
Apogee Separation Bay
Motor
5
Vehicle Dimensions
Body
Tube
◦ 5.5 in dia.
Can
◦ 2.0 in dia.
6
Launch Vehicle Verification
Vehicle/Payload
design justification
Static stability analysis
Materials/system justification
(discussed in further detail in proceeding slides)
7
Vehicle Design Justification
Different
ideas for reducing drag
Requirements
◦
◦
◦
◦
◦
Stable
Fast
Precise
Consistent
Highly variable
8
Vehicle Materials
Nosecone
Body
Cans
Fins
Polystyrene Plastic
Blue Tube (Apogee Comp.)
Blue Tube (Apogee Comp.)
G10 fiberglass
9
Material Justifications
Phenolic
Tubing
◦ Cured paper fibers
◦ Cheapest, strong, brittle
Blue
Tube 2.0
◦ High-density paper
◦ More expensive, durable, dense
Carbon
Fiber
◦ Strands of woven carbon
◦ Most expensive, strongest, labor-intensive
10
Static Stability Margin
1.5
in neutral configuration pre-launch
2.4 after engine burnout
◦ Drag mechanism actuated
RockSim
estimated CP/CG locations
On the unstable side
Add mass to nose of rocket
11
Recovery Scheme
Two
Separations
◦ Apogee
Drogueless
◦ 500 Feet
Main Parachute
Double
Redundancy
◦ Flight computer
◦ Altimeter
500 Feet
Apogee
12
Vehicle Safety Verification Plan
This matrix shows
detrimental failures in
red, recoverable
failures in yellow, and
failures with a minimal
effect in green
13
Testing Plans
Ground
test proper body tube separation
during E-Charge ignition
Use
a multimeter to measure the current
the Flight Computer sends to each ECharge during ground simulations
Servo
selection through torque testing on
flap from collected simulation/wind tunnel
data
14
Motor Selection
Motor
Manufacturer:
Loki
Motor Designation:L1482-SM
Total Impulse:
868.7 lb-s
Mass pre/post burn:
Pre:7.8 lb
Post:3.8 lb
15
Thrust-To-Weight Ratio
16
Rail Exit Velocity
Rail
Exit Velocity: 85.1 ft/s
Rail Length:
10 ft
17
Recovery Avionics
Raven Flight Computer
Competition Altimeter
4 Total E-Charges
2 from Flight Computer
2 from Altimeter
1
◦
1
1
◦
1
Main Apogee Charge
@ 5280 feet
Backup
Main Chute Charge
@ 400 feet
Backup
Apogee TB
9V Batteries
AvBay
Flight
Computer
Competition
Altimeter
Positive TB
Main Chute
TB
18
Aerodynamics-Linear Flaps: i.
Flap
Geometry
0% closed corresponds to the position
where the flap is not exposed to air flow
100% closed corresponds to where the flap
is fully extended into the flow
Flap Max % Closed
A
100
Flap End
Geometry
Semi-Circle
Can Inner Dia
[in]
1.504
Flap Width [in]
B
100
Semi-Circle
2.551
2.551
C
65
Rectangular
2.551
2.551
D
75
Rectangular
2.551
2.051
1.504
19
Aerodynamics-Linear Flaps: ii.
Flap A
Flap B
20
Aerodynamics-Linear Flaps: iii.
Flap C
Flap D
21
Aerodynamics-Linear Flaps: iv.
Drag
data from cases run at 300 m/s
Flap
A
B
C
D
Maximum Drag [N]
81.7235
240.396
204.086
197.838
*NOTE: All flap data is for one flap and all rocket data is for half-body
22
Aerodynamics-Rotating Flaps: i.
Moment
Concerns with the y component of
the force generated by the flap at various
angles
Analyzed at the most extreme case (largest
can and flap size at 45 ̊)
Force in the y direction caused by the flap
angle deflection is negated by the force it
creates on the wall of the can
Component
Rocket
Force in y-direction [N]
-199.8
Flap
199.61
*NOTE: All data is from a simulated wind speed of 300 m/s
23
Aerodynamics-Rotating Flaps: ii.
ANSYS Fluent CFD mesh
sizes were refined in areas
of interest such as the flap
and the interior wall for
optimal results.
24
Structures-Can Analysis
Analyzed
the worst case scenario (flaps
100% closed)
Pressure forces in front of the valve are
not a concern
Low pressure pockets behind the valve are
not a concern
25
Controls: i.
Proportional
Integral Derivative (PID)
controller that will induce pressure drag as
a means of regulating vehicle altitude
Drag is calculated dynamically during flight
Controller should respond to physical
system changes in no more than 50
milliseconds and recover within 2% of the
goal altitude
26
Controls-System Model: ii.
Dynamic Apogee-Rectifying Targeting (DART) Control System
Dynamic Target: Used to aid in assuring the mean energy path solution is
followed
Restrained Controller: Proportional Integral Derivative (PID) derived
controller with physical limits
Physics Plant: Simulation of vehicle-environment interaction given controller
commands
Instrument Uncertainty: Propagation of instrument uncertainty into system
values
Alt. Projection: Projection of rocket apogee altitude with same physics plant
model for consistency
27
Controls – Dynamic Target
Controls – Restrained Controller
Controls - Physics
Controls –Instrument Uncertainty
Controls – Apogee Calculation
Flight Avionics
Drag Servo
Competition Altimeter
Drag Computer
Drag Servo
9V Batteries
Drag
Computer
Competition
Altimeter
33
Propulsion
Select
a motor such that it will allow our
rocket to exceed one mile in our minimum
drag configuration
34
Payload Design
Drag Control System
Actuating flaps
located within side
cans to control drag
Control system will
activate under
specific altitude
and/or velocity
conditions
35
Payload Test Plan i.
Flap
Drag Testing
Simulations/flow characterization using
compressible flow in ANSYS Fluent CFD over
a range of Mach numbers
Test drag flap mechanism in various
configurations to confirm results from
simulated model
Produce a function for control system
relative to drag, flow speed and flap
deflection
36
Payload Test Plan ii.
Drag Flap Control System Testing
4 constants to vary (Kp, Ki, Kd, Dt)
N^4 simulations for N possible different
constants
Parallel processing in Matlab to tackle
Monte Carlo simulation
NYX / FLUX supercomputers from UM
Center for Advance Computing used to
tune constants for best performance
37