Transcript controller
Electrical ENgg. Department
Simulation of elevator using Simulink
Any drive system consists
of:
- Power Source
- Electronic Converter
- Motor
- Mechanical Load
- Controller
- Feedback loops
The scheme of elevator structure is shown in Fig. A drive belt is
looped over a drive pulley with the ends anchored to the top of
the elevator shaft. The electric drive is rigidly attached to the drive
pulley with the use of gearing. The car and counterweight, which
ride on pulleys, provide belt tension ensuring the toothed belt and
drive pulley do not slip. The elevator car and counter-weight are
of different weight .
GOAL: IS TO HAVE CONSTANT SPEED AND
RESPONSE TIME REGARDLESS OF THE LOAD
TORQUE
Mathematical Model of Elevator
Electric Drive .
equations that control operation of the elevator can be divided two
systems :
- Mechanical system .
- Electrical System .
Mathematical Model of Mechanical
System’s
The motion equation of the entire system from the motor’s perspective is:
𝑇𝑒 = 𝐽𝑚
𝑑𝜔𝑚
𝑑𝑡
+ 𝐵. 𝜔𝑚 + 𝑇𝐿
where:
𝐽𝑚 is the motor’s moment of inertia
𝜔𝑚 is the angular speed of the rotor
B is the friction coefficient of the motor
𝑇𝐿 is the load torque placed on the motor’s shaft
(1.1)
The load torque 𝑇𝐿 that is placed on the drive pulley which is mounted on
the motor’s shaft is expressed in equ 1.2
𝑇𝐿 = 𝑅𝑝 𝐹𝐿 + 𝐽𝑝
𝜔𝑃 is the angular speed of the pulley
𝐽𝑚 is the pulley’s moment of inertia
𝑅𝑝 is the radius of the drive pulley
𝐹𝐿 is the force exerted on the drive pulley
𝑑𝜔𝑃
𝑑𝑡
(1.2)
If the elevator car is moving upwards the load force is defined by equ 1.3
𝐹𝐿 = 𝑔 𝑀𝑐 − 𝑀𝑐𝑤 + 𝑀𝑐
where:
𝑔 is the gravitational constant
𝑀𝑐 is the mass of the car
𝑀𝑐𝑤 is the mass of the counter-weight
𝑉𝑐 is the linear speed of the car
𝑑𝑉𝑐
𝑑𝑡
(1.3)
The car speed expressed in terms of motor speed is expressed as:
𝑉𝑐 = 𝑅𝑝 𝜔𝑝
In Equ. 1.3 the force 𝐹𝐿 is affected by the gravitational force𝐹𝐿𝑔 and the
inertia of the elevator car 𝐽𝑐 , both of which are expressed as:
𝐹𝐿𝑔 = 𝑔 𝑀𝑐 − 𝑀𝑐𝑤
𝐽𝑐 = 𝑀𝑐
The car speed expressed in terms of motor speed is expressed as:
𝑉𝑐 = 𝑅𝑝 𝜔𝑝
𝑑𝑉𝑐
𝑑𝑡
(1.4)
(1.5)
(1.6)
(1.4)
Equ. 1.2 The load torque is now expressed as:
𝑇𝐿 = 𝑅𝑝 𝑔 𝑀𝑐 − 𝑀𝑐𝑤 + 𝑅𝑝2 𝑀𝑐
Substituting the load torque equation for when the elevator car is moving
upwards (Eqn. 1.7) into the motor’s motion equation (Eqn. 1.1), the motion
equation of the entire system is obtained as:
𝑑𝜔𝑝
𝑑𝑡
+ 𝐽𝑝
𝑑𝜔𝑃
𝑑𝑡
(1.7)
𝑇𝑒 = 𝐽𝑚
(1.8)
𝑑𝜔𝑚
𝑑𝑡
+ 𝐵. 𝜔𝑚 + 𝑅𝑝 𝑔 𝑀𝑐 − 𝑀𝑐𝑤 + 𝑅𝑝2 𝑀𝑐
𝑑𝜔𝑝
𝑑𝑡
+ 𝐽𝑝
𝑑𝜔𝑃
𝑑𝑡
and the load torque due to gravity is:
𝑇𝐿𝑔 = 𝑅𝑝 𝑔 𝑀𝑐 − 𝑀𝑐𝑤
where the equivalent moment of inertia is:
𝐽𝑒𝑞 = 𝐽𝑚 + 𝑅𝑝2 𝑀𝑐
Using gear ratio a
𝜔
𝑎 = 𝜔𝑚 (1.11)
𝑝
Mathematical Model of Electrical
System’s :
Why to choose series motor ?
1- Highest starting torque.
2 - Draws less current and power from the
source compared to a shunt or
compound motor.
In general case we can derive an expression for the motor which is
𝑉𝑡 = 𝑅𝑎 𝐼𝑎 + 𝐿𝑎
𝑉𝑡 is Terminal voltage of DC motor
𝑅𝑎 is armature resistance
𝐿𝑎 is armature inductance
And 𝐸𝑎 = 𝐾𝜑𝜔𝑚
K is constant
Let 𝑉𝑓 = 𝑅𝑠 𝐼𝑓 + 𝐿𝑠
𝑑𝐼𝑎
𝑑𝑡
+ 𝐸𝑎 + 𝑅𝑠 𝐼𝑓 + 𝐿𝑠
𝑑𝐼𝑓
(2.1)
𝑑𝑡
𝐸𝑎 is back e.m.f Voltage
𝑅𝑠 is Filed resistance
𝜑 is magnetic field
𝑑𝐼𝑓
𝑑𝑡
From 2.1,2.2 and 2.3 we can get
𝑑𝐼
𝑉𝑡 = 𝑅𝑎 𝐼𝑎 + 𝐿𝑎 𝑎 + 𝐾𝜑𝜔𝑚 + 𝑉𝑓
𝑑𝑡
𝐼𝑓 Filed current
(2.2)
(2.3)
𝐿𝑠 Filed inductance
(2.4)
𝜔𝑚 is output motor speed [rad/s]
Closed loop control is when the firing angle of the power processing unit is
varied automatically by a controller to achieve a reference speed or
torque
This requires the use of sensors to feed back the actual motor speed and
torque to be compared with the reference values.
•Actual motor speed measured using the tachogenerator (Tach) is
filtered to produce feedback signal
•The reference speed is compared to motor obtain a speed error signal
•The speed (PI) controller processes the speed error and produces the
torque command Te
•Ia is compared to actual current Ia to obtain a current error signal
•The current (PI) controller processes the error to alter the control signal vc
• vc modifies the firing angle to be sent to the converter to obtained the
motor armature voltage for the desired motor operation speed
We Built The Drive System with:
Dc Series Motor ( The parameters of Motor were taken from the library )
Max passenger weight = 600 Kg
Cabinet weight = 100 Kg
Counter weight = 400 Kg
Pully Diameter = 30 cm
Vf consat = 300 V
Flux assumed to be = .2
Matlab Blocks:
UpWard
Case 1 : Max : 600 Kg passenger weight ( Total Of 700 Kg with Cabinet )
UpWard
Case 2 : 300 Kg Passenger weight ( total Of 400 Kg = Same as Counter
weight )
UpWard
Case 3 : 0 Kg passenger weigh (Total of 100 Kg less than Counter weight )
Downward
Case 4 : Max : 600 Kg passenger weight ( Total Of 700 Kg with Cabinet )
Downward
Case 5 : 300 Kg Passenger weight ( total Of 400 Kg = Same as Counter
weigh )
Downward
Case 6 : 0 Kg Passenger weight ( total Of 100 Kg = less than Counter
weight